Jenn-Air RISE JFFCC72EHL Guide De Démarrage Rapide

OPERATING INSTRUCTIONS
IMPORTANT: Before operating this appliance, make sure it has been properly installed according to the
appliance's Owner's Manual.
The Temperature Control UI is located above the external dispenser and on the side of the left
refrigerator door. For your convenience, your refrigerator and freezer controls are preset at the factory.
For your convenience, your refrigerator and freezer temperature controls are set to the recommended set
points at the factory. When you first install your refrigerator, make sure the temperature controls are still
set to the recommended set points. The recommended set points are 37°F (3°C) for the refrigerator and
0°F (-18°C) for the freezer.
IMPORTANT:
� The recommended settings should be correct for normal
� When the power is on, the temperature display shows the set
� Wait 24 hours for your refrigerator to cool completely before
� If the temperature is too warm or too cold in the refrigerator
� Wait at least 24 hours between adjustments. Recheck the
TEMPERATURE SET POINTS
1. Touch [—]/[+] for Refrigerator or [—]/[+] for Freezer and toggle through temperature set points.
NOTE: To view temperature in degrees Celsius, touch and hold the [°F/°C] button for 3 seconds and
the temperature display will change. To return to Fahrenheit, touch and hold the [°F/°C] for 3 seconds
and the temperature display will change.
To activate Temperature mode for Drawer, touch Drawer and toggle through 4 optional temperature
settings: Meats and Fish, Cold Drinks, Deli and Cheese, and Wine. The display will show the
temperature set point of the selected setting for the Drawer.
Recommended Refrigerator Temperature
Fridge set point range: 33°F to 45°F (0°C to 7°C) Freezer set point range: -6°F to 5°F (-22°C to
When adjusting temperature set points, use the following chart as a guide.
CONDITION:
Refrigerator too cold
Refrigerator too warm
Freezer too cold
Freezer too warm / too little ice
2. Touch [—]/[+] to adjust the Refrigerator zone. The display will show the temperature set point of the
selected compartment as shown.
3. When the temperature in is the range of Pure Freeze(R), the display will light up. Pure Freeze(R) is
activated at the coldest Freezer set point.
Pure Freeze(R) FEATURE
This feature acts on the most-relevant storage parameters that must be controlled to minimize moisture
migration from frozen food. This in turn reduces the freezer burn occurrence.
� To turn on the Pure Freeze(R) feature, toggle to the coldest Freezer temperature set point.
� To turn off the Pure Freeze(R) feature, toggle from the coldest freezer set point to any other
temperature.
SOUND ON/OFF
The Sound button allows the customer to turn the sound on and off.
� To turn on the Sound feature, press the Sound button. When the button is pressed, the Sound icon
will blink 3 times and appear on the display screen.
� To manually turn off the Sound feature, press the Sound button and the display will blink 3 times and
turn off.
W11487620B
W11487622B-SP
French Door Bottom Quick Start Guide
household refrigerator use. The controls are set correctly
when milk or juice is as cold as you like and when ice cream
is firm.
NOTE: Areas such as a garage, basement, or porch may
have higher humidity or extreme temperatures. You may
need to adjust the temperature away from the recommended
settings to accommodate for these conditions.
point temperature of the compartment.
adding food. If you add food before the refrigerator has
cooled completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer controls to a
colder than recommended setting will not cool the
compartments any faster.
or freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
temperatures before other adjustments are made.
Recommended Freezer Temperature
-15°C)
TEMPERATURE ADJUSTMENT:
Refrigerator setting 1° higher
Refrigerator setting 1° lower
Freezer setting 1° higher
Freezer setting 1° lower
MAX COOL/MAX ICE
The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm
room temperatures.
The Max Ice feature assists with increasing the cooling for the freezer compartment in order to increase
ice production.
� To turn on the Max Cool/Max Ice feature, press the Max Cool/Max Ice button. When the button is
pressed, the icon will blink 3 times and appear on the display screen.
� To manually turn off the Max Cool/Max Ice feature, press the Max Cool/Max Ice button and the display
will blink 3 times and turn off. The Max Cool/Max Ice feature will remain on for 24 hours unless
manually turned off. Adjusting the refrigerator temperature will automatically turn off the Max Cool/
Max Ice feature.
NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.
WATER FILTER RESET
Displays the status of the water filter. To reset the water filter, press Max Ice and Max Cool for 3 seconds.
After countdown, the Good icon will blink 3 times and remain lit.
The water filter reset lights will let you know when to replace the water filter. See "Water Filtration
System" in the Owner's Manual.
� Yellow: ORDER—Order a replacement filter.
� Red: REPLACE —Replace the water filter. While you are dispensing water, Replace Filter icon will
flash constantly from beginning to the end of dispensing. After 14 days without replacing the Water
Filter, the Replace Filter icon will blink 7 times and an alert tone will sound 3 times, at the end of
dispensing. See "Water Filtration System" section in the Owner's Manual.
NOTE: "Replace Filter" will remain illuminated if a filter reset is not done.
Touch Max Cool and Max Ice at the same time on the temperature control display for 3 seconds to reset
water filter. The display will do a 3 second countdown and then flash the icon and play a tone.
Filter Status
®
The JennAir app will send an alert that displays the water filter status.
POWER OUTAGE
The Power Outage indicator lets you know if the power supply to the refrigerator has been off and the
freezer temperature has risen.
The control panel display will read "Power Outage" and an alert tone will sound 3 times. Touch any button
to stop the tone and turn off the Power Outage icon.
Once the power outage has been confirmed, "Power Outage," will disappear.
SABBATH MODE
Sabbath mode is designed to have all the benefits of saving even more energy, yet maintaining food
freshness.
The freezer and refrigerator user set points remain unchanged while in this mode. If you unintentionally
turn on Sabbath mode, the word "Sabbath" will light up on the display. Enter and exit Sabbath mode by
pressing and holding °F/°C and Sound at the same time for 3 seconds.
NOTE: You will be unable to dispense or change temperature set points in Sabbath mode. Your interior
lighting and control panels will all be inactive in Sabbath mode.
SHOWROOM MODE
This mode is used when the refrigerator is on display in a retail store or if you want to turn the cooling off
and deactivates all other functions except interior lighting. Showroom mode can be used when going on
vacation, see "Vacation and Moving Care" section for proper steps on leaving your refrigerator in this
mode for long periods of time.
If you turn on Showroom mode, the word "Showroom" will light up on the display. Enter or Exit Showroom
mode by pressing and holding °F/°C and Drawer at the same time for 3 seconds.
NOTE: Empty ice maker if refrigerator is going to be turned off for an extended period of time.
INTERNET CONNECTIVITY GUIDE
Connectivity requires Wi-Fi and account creation. App features and functionality subject to change. Data
rates may apply.
Once installed, launch the app. You will be guided through the steps to set up a user account and to
connect your appliance. If you have any problems or questions go to www.jennair.com/connect
Online Ordering Information
For detailed installation instruction and maintenance information, winter storage, and transportation tips,
please see the Owner's Manual included with your appliance.
For information on any of the following items, a full cycle guide, warranty, detailed product dimensions, or
for complete instructions for use and installation, please visit https://www.producthelp.jennair.com, or in
Canada https://www.jennair.ca/support. This may save you the cost of a service call. However, if you
need to contact us, use the information listed below for the appropriate region.
United States:
1-800-536-6247
JennAir (R)) Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022–2696
SAVE THESE INSTRUCTIONS
Canada:
1-800-536-6247
JennAir (R) Appliances
Customer eXperience Center Whilrpool Canada
200–6750 Century Ave.
Mississauga, Ontario L5N 0B7