Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Warning: risk of accidental injury or drowning: do not
use whirlpool bathtub unless all suction guards are installed to
prevent body and hair entrapment;
Warning: to avoid injury, exercise care when entering or
exiting the whirlpool bathtub;
Warning: risk of electric shock: do not permit electric
appliances (such as a hair dryer, lamp, telephone, radio or
television) within 1.5 m (5 ft.) of this whirlpool bathtub;
Caution: test the ground fault circuit interrupter, (GFCI)
protecting this appliance periodically in accordance with the
manufacturer's instructions;
Warning: risk of hyperthermia and possible drowning:
water temperature in excess of 40º C
hazardous
to your health. Check and adjust water
temperature before use.
Warning: keep hair and clothing a minimum of twelve
inches away from all suction fittings and drains at all times.
Persons with long hair should either secure hair to a minimum
length or wear a bathing cap.
Safe use of a whirlpool bath
Your physiological response to a whirlpool bath depends on
your age, health and medical history. Initially, only stay in the
bath for a short time until you learn your tolerance for hot water.
If you develop a headache, become dizzy or nauseous, get out
at once and cool off under a shower. Get medical help if
symptoms persist.
Consult your doctor before you use the whirlpool for physical
therapy of an injury or disorder. Don't take a whirlpool bath
without your doctor's consent if you are ill, pregnant, if you
suffer from high blood pressure, heart disease, or other health
problems. Never take a whirlpool bath while under the
influence of medication, drugs, or alcohol.
Warning
Do not run the whirlpool pump unless the bath is filled with
water to a level of 2" (50 mm) above the whirlpool fittings.
Use only a small amount of soap or other bath preparation in
whirlpool baths. Otherwise, excessive foaming may occur.
Suction
Do not block suction inlet screen on whirlpool baths. Water is
circulated back to the pump from this location. Should the inlet
screen become blocked in any way the safety suction will
engage and the pump will start cavitation. The pump will
immediately shut down stopping the flow, thus releasing
whatever is blocking the screen. When the screen is free of
blockage, the pump will automatically start up and the system
is back to normal. Under no circumstance is the pump to be
used without the screen on the suction return.
OPERATING INSTRUCTIONS
Air Switch
Press the tub mounted air switch to start the pump. The pump
will run continuously. Press the air switch (A/S) again to stop.
Whirlpool Fittings
Use a finger to swivel the whirlpool jet to give the direction of
flow required. Do not plug the whirlpool fittings while the pump
is running.
The flow of water can also be increased by turning the jet
face plate clockwise and decreased by turning
counterclockwise. Refer to Figure 8.
Caution: The whirlpool jets can be misadjusted to
throw a stream of water out of the tub onto the floor.
Drain the Bath
Check that the pump is not running. Drain the whirlpool
bath after each use. It is not a spa that can retain its water
for repeated use through continuous filtration, heating and
chemical treatment.
(104º F) may be
Motor Protection
The pump motor is equipped with a built-in thermal
overload protector to shut off the motor in the event the
temperature becomes excessive (as a result of
mechanical or electrical problems; such as low voltage,
poor ventilation, overload lines, etc.). The motor will restart
automatically as it cools down.
FIGURE 8 - ADJUSTABLE FLOW WHIRLPOOL JET
WHIRLPOOL OPTION
IN-LINE HEATER
Your whirlpool bath heater utilizes "Smart Technology" to
offer you years of bathing pleasure. The advanced
electronic design provides trouble free operation
precise control of water temperature.
NOTE: The heater is controlled by a vacuum switch. The
whirlpool must be running for the heater to function.
There are no adjustments necessary, after the whirlpool is
filled with hot water the heater will maintain 104°F water
temperature. To cool the water simply add cold water as
desired.
High Limit Protection: In the event the water temperature
exceeds 114°F the heater will automatically shut-off. To
reset, wait until the water temperature drops below 104°F,
3
W
G
B
B - BLACK
G - GREEN
W - WHITE
and
Specifications:
1.5 kW "Inline"
115 Volt, 20 Amp
Vacuum switch
R0084092, Rev. B
Publicité
Table des Matières
