Getting Started - VOLTCRAFT VC-WL 60/200 Mode D'emploi

Part Name
■
1 1x trolley handle
■
2 4x handle screws
1. Insert the handle into the handle slot.
2. There are 2x screw holes on each side of the handle slot. Fasten the screws to secure the handle in
the slot.
6.2 Wheels
6.2.1 Wheel parts
Part Name
■
1 1x wheel axle
■
2 4x stand screws
■
3 2x c-clips (for axle)
■
4 2x wheel hub caps
■
5 2x wheels
■
6 1x trolley stand
■
7 2x wheel bearing hub washer
6.2.2 Assemble wheels
Assemble parts as shown.

7 Getting started

7.1 Check battery compatibility
■
Check the battery information marked on the battery label.
■
Check if the battery type is supported by this product. See:
7.2 Prepare vehicle and battery
■
Switch accessory loads OFF (e.g., air conditions, lights, radio).
■
Disconnect / switch OFF items connected to auxiliary power outlets (e.g., GPS, cameras).
■
Remove the key from the ignition.
■
Allow vehicle parts to completely cool down.
■
Make sure battery terminals are clean.
5
Technical data [} 6].
8 Connection
Important:
Observe the following information when connecting or disconnecting tester leads to a battery.
WARNING: Risk of electric shock. Disconnect the product from the power supply before con-
necting or disconnecting leads to the battery.
8.1 Connecting cables to battery
Preconditions:
a
Battery contact terminals are clean.
a
Vehicle engine and electrics are switched OFF.
a
The product is disconnected from the power supply.
1. Connect the red (+) clamp to the positive (+) battery terminal.
2. Connect the black (-) clamp to the negative (-) battery terminal.
3. Wiggle the clamps back and forth to ensure good contact.
Note:
Refer to the vehicle manufacturer instructions for alternative connection points.
8.2 Disconnecting cables from battery
1. Disconnect the product from the power supply.
2. Disconnect the black (-) clamp to the negative (-) battery terminal.
3. Disconnect the red (+) clamp to the positive (+) battery terminal.
9 Operation
9.1 Charging batteries
WARNING: Explosive gases. Prevent flames and sparks. Provide adequate ventilation dur-
ing charging.
Preconditions:
a
The product is not connected to the power supply.
a
You have checked the battery rating plate for compatibility (battery type and voltage).
1. Connect the product to the battery. See:
2. Connect the product to the power supply.
à
The display will show the battery voltage.
3. Press the "MODE" SELECT button to choose "12V Charge" or "24V Charge".
4. Press the "CURRENT" SELECT button to choose "12V (10A, 30A, 60A)" or "24V (5A, 15A, 30A)".
5. Press the "TYPE" SELECT button to choose a battery type "STD", "AGM", or "GEL".
6. Press the START|STOP button to start/stop charging.
7. When charging is complete, disconnect the product from the power supply.
8. Disconnect the product from the battery. See:
9.2 Jumpstarting
Notes:
– The jump start function can be used to help start vehicles with a weak battery.
– In very low temperatures or if the battery voltage reading on the display is below 8.5 V, it is recom-
mended to charge the battery at least 5 minutes before attempting to jump start.
1. Connect the product to the battery. See:
2. Press the "MODE" SELECT button to enter "12 V BOOST" mode.
3. Press the START|STOP button to start boosting.
à
The display will show the countdown time.
à
The product will deliver a 30 A charge until the engine starts.
4. Try to start the vehicle using the ignition switch.
Connecting cables to battery [} 5].
Disconnecting cables from battery [} 5].
Connecting cables to battery [} 5].