NEO TOOLS 90-070 Instructions page 6

3.1 Housing of steel plate and coated by heat-resistant powder .
3.2 Supplied complete with cord and plug .
3.3 Description of Control Panel:
3.3.1 Left Knob: selector with heat setting
3.3.2 Right Knob: Thermostat dial
3.3.3 Power light:Above is the power indicator light
3.3.4 Work indicating lamp: Below is the work indicator light
4. Introduction:
4.1 Depending on the power cord type this fan heater may be used only in household, warehouses and workshops,It incorporates a Adjustable
trip thermostat and a self-resetting thermal cut-out to control the heating elements. The thermostat feels the air temperature and controls the
surrounding temperature.The fan motor is not controlled by thermostat and it keeps on working when the thermostat cuts off the heating
element.The self-resetting thermal cut-out will switch off the heater to ensure the safety when overheating.
4.2 When using the heater for the first time, you may notice a slight emission of smoke. This is quite normal and it stops after a short time. The
heating element is made of stainless steel and was coated with protection oil by production. The smoke is caused by the left oil when heated.
5. Using Instructions:
5.1The machine is equipped with a Adjustable trip thermostat, which automatically shuts down when the machine is not in an upright position
(falling back and forth).When it is moved to an upright position, the device will return to normal operation.Always keep the machine upright before
starting
5.2Position the fan heater so that it stands upright on a firm surface and at a safe distance from wet environments and flammable objects.
5.3 Connect the fan heater to the mains.
5.4 Set the Adjustable trip thermostat knob to the MAX and let the heater operate with full power.
5.5 The fan heater will switch on when the heating selector is set to one of the power settings.
5.6 Once the room reaches the required temperature, heating element will stop working but fan also working .Once the temperature decreased,
the heating element will be working. The fan heater now starts and stops automatically and thus keeps the room temperature constant.
5.7 Before switch off the heater, please turn the thermostat to MIN position and turn the switch to fan position, let the appliance cool down for
two minutes then turn off the heater and pull out the plug.
6. Trouble shooting:
You can solve many common problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve
the problem before calling the service centre.
Problem
The heater does not operate, even
when it is plugged in and the
switch, thermostat are switched on
.
The heating element glowing
The appliance didn't heat up, or
only ventilator worked
Abnormal noise
7.Cleaning and Maintenance：
7.1 Before cleaning the appliance,disconnect it from the socket and let it cool down. The enclosure is easily to get dirty, wipe it often with soft
sponge. For every dirty parts, wipe with a sponge dipped in <50°C water and mild detergent, then dry the heater enclosure with clean cloth. Be
Possible cause
The plug is loose, bad connection
No power in socket outlet
The input voltage is too high or too low
The air inlet grill is blocked
The switch was not put at heating setting
The thermostat operated
The self-resetting cut-out operated
The appliance is not stands upright
Treatment
Pull out the plug, check the connection of the plug
and socket. Then connect again.
Insert the plug in a proper socket
Use power supply according to the rating on the
label
Keep the heater far way from articles like curtain,
plastic bag, paper and other things which can
cover the inlet or can be easily cover on the air
inlet
Turn the switch to heat setting
Turn the thermostat and listen if there is
open/close voice. If there is no click and the
thermostat is not damaged, the heater will
automatic switch on when the appliance cooled
down
Turn the heater off and inspect the blockage of
inlet or outlet. Disconnect the plug and wait at
least 10 minutes for the protection system to reset
before attempting to restart the heater.
Put the heater on a level surface