Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame
rail
Hitch Shown In Proper Position
Equipment Required: Spray lubricant, Paint,
Pull wire (Provided)
Fastener Kit: 24818F
Wrenches: 11/16", 3/4"
Drill Bits: 1" Hole Cut Saw or drill
Enlarge Hole OR Drill Hole
Note: Fasteners typical both sides
1
Qty. (2)
Carriage bolt 7/16-14 X 1.50 Gr5
2
Qty. (2)
Conical washer 7/16
3
Qty. (2)
Hex nut 7/16-14
4
Qty. (2)
Spacer ( small sq holes)
1.
Lower exhaust system at the rubber isolator (3). Spraying a lubricant on the metal hanger rod and the rubber isolator helps
removal.
2.
Enlarge the access holes in the vehicle to accept the spacer. OR Drill 1" access hole in bottom of each frame rail.
3.
Feed pull wires with spacer and bolt into frame rail thru 1" drilled hole and out the attachment holes. Leave pull wire attached
4.
Paint any exposed metal.
5.
Raise hitch into position and attach as shown in Figure 1. Remove pull wires and attach conical washers and nut (be careful
not to push fastener back into frame rail). Hand tighten.
6.
Attach hitch to tow hook as shown in Figure 1. Orient the spacers with respect to the tow hook as shown.
7.
Check to assure hitch is centered on vehicle.
8.
Torque all fasteners to specifications.
9.
Raise exhaust system back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2008 Cequent Towing Products
Installation Instructions
Fascia
Drawbar must be used in the
RISE position only.
Tow Hook
8
Frame Rail
7 6
Tighten all ½ GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Suzuki SX4 Sport
Drawbar Kit:
3593
1
4
2
3
5
Figure 1
5
Qty. (1)
6
Qty. (1)
7
Qty. (1)
8
Qty. (1)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Kink Pull wire to keep
spacer independent of
bolt
Carriage bolt 1/2-13 X 2.25 Gr5
Conical washer 1/2
Hex nut ½-13
Spacer
24818N
6-26-08
Part Numbers:
24818
60204
77190
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 24818
Sommaire des Matières pour Cequent Towing Products 24818
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008 Cequent Towing Products Sheet 1 of 3 24818N 6-26-08 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24818N 6-26-08 Rev. A 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 24818N 6-26-08 Rev. A 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...