Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
17 Settings of the handset (customisations)
Handset Name
The predefined name is "Handset 1". To change it, press MENU > TELEPHONE > HANDSET NAME.
Type in the customised name (max. 8 characters) and confirm by pressing OK.
To recover the predefined name of the handset ("HANDSET 1"), repeat the above sequence by deleting the customised name and
confirm by pressing OK.
Language of the menu
The predefined language must be selected at the first use of the telephone.
To change it, press MENU > TELEPHONE > LANGUAGE.
Using the
Automatic answer
When the automatic answer is active, upon any incoming call, if the handset is positioned on the base, it will be sufficient to lift it to answer.
When the automatic answer is not enabled, to answer a call it is always necessary to press any key.
Press MENU > HANDSET > AUTO ANSWER. By using the
and confirm by pressing OK.
Key Beep
Press MENU > HANDSET > SOUND > Key Beep.
To enable or disable the tones, played when keys are pressed on the handset (ON/OFF and confirm by pressing OK).
Modifying the handset PIN
The telephone PIN is needed to perform one of the 3 Reset types available for the handset (see the next paragraph).
Press MENU > HANDSET > PIN HANDSET.
Insert the current PIN of the handset (4 digits, the default pin is 0000) .
Insert the new PIN and press SAVE. The message "Stored !" will appear. Now the handset has its new PIN.
NOTE:
it is recommended to take note of the new code typed in, and to keep this information in a safe place.
Resetting the Handset
When resetting the handset the following information will be deleted:
SETTINGS: the handset settings reported under chapter 6 are re-established with the exception of the phonebook, the lists of
1)
calls and the handset PIN, and the registration information of the handset in hand are kept in memory as well at the relevant
bases.
2)
HANDSET: all settings related to the handset and reported under chapter 6 will be defaulted, including the information concer-
ning the bases where the handset has been registered. To perform one of the two types of reset above, press MENU > HANDSET
> SET DEFAULT. When requested, type in the handset PIN. The message "Reset all settings?" will appear, confirm the reset by
pressing the function key OK.
For correct use, after resetting the handset, switch the handset on and off again, resetting the language upon
switching on again.
Baby Monitor
Press MENU > EXTRA MENU > BABY MONITOR > MODE > EDIT.
By using the
By using the
BABY MONITOR: By using the
SAVE to store it.
18 Conformity of the product to the safety regulations
The PROMELIT S.p.A. company, seated in Via Modigliani n° 20, in Cinisello Balsamo (Milano), herewith declares that the TULIP product is
compliant with the basic requirements and the other relevant provisions, as established by the R&TTE Directive 1999/5/EC.
In particular the product is conformal to:
Radio Part: ETSI EN 301-406 V2.1.1 (TBR 6).
Electromagnetic compatibility (EMC): ETSI EN301 489-1 V1.8.1, EN301 489-6 V1.3.1
Electrical safety: EN60950-1:2006+A11:2009
The conformity to such requirements is expressed by the
above address. The information card for the product end-of-life is stored at the Quality Department of the "Promelit S.p.A. " company.
NOTE:
The telephone requires electric supply to be able to operate. Use the product only with the power supply provided
with the equipment.
User Manual mod.
tto_guida_22072011_v.indd 21
keys select one of the available languages and confirm your choice by pressing OK.
keys select one of the two options below and press OK BABY CALL:
keys select Call To ("internal" or "external"), and press SAVE to store it.
keys select the SENSITIVITY ("high" or "low ") and Call To ("internal" or "external"), then press
keys select "ON" (to enable the automatic answer) or "OFF" (to disable)
marking. The original declaration of conformity is available at the
11
25/07/2011 11:12
Publicité
Table des Matières
