Multi-Handset Configuration; Internal Calls (Between Handsets Associated To The Base); Call Transfer And Three-Way Conference (2 Handsets + 1 External); Multi-Base Configuration - ProMinent TULIP Notice D'instructions

14 Multi-handset configuration

Internal calls (between handsets associated to the base)

To call another handset associated to the same TULIP base (see the previous chapter), press MENU > EXTRA MENU > INTERNAL CALL.
Select the HANDSET you want to call ("All" in case you wish to call all the connected handsets) and press OK.
To answer an internal call, proceed as for the external calls.

Call Transfer and Three-way Conference (2 handsets + 1 external)

During a call between one handset (e.g. HANDSET 1) and one external party, press the Menu key on HANDSET 1 and select INTERNAL
CALL. Choose from the list on display the telephone number to call (e.g. HANDSET 2) and press OK (the external user will remain on hold).
When HANDSET 2 will answer, it is possible to:
1) Transfer the external call to HANDSET 2: it is sufficient to press the
2) Activate a three-way conference: press Menu on HANDSET 1 and choose Conference. By pressing instead "INT Call End" on
HANDSET 1, the second handset is disconnected and HANDSET 1 will be connected back to the external caller.

15 Multi-base configuration

Thanks to the GAP profile, which the device is equipped with, it is possible to affiliate your own handset to more than one DECT
bases (even from different brands and models), provided they are also equipped with the GAP profile. Each TULIP handset can be
registered on 4 bases as a maximum.

Registration of an TULIP handset on a second base.

To register the TULIP handset on a second TULIP base, the procedure is the same as illustrated under chapter 13 "Registration of an
handset on a base" (Affiliation).
To register instead the TULIP handset on a base from a different model, set the latter in registration mode as described in the related
user manual, then follow the affiliation procedure on the TULIP handset as described under chapter 13 (typing in when requested
the PIN code of the second base).

Registration of an handset of a different model on the TULIP base

Keep pressing the "Handset Searching" key on the TULIP E base for about 5 seconds, then follows the instructions reported on the
user manual of the handset of the other manufacturer (typing in when requested the PIN code of the TULIP E base).

Select one base

If the handset is registered on more than one bases (4 different bases are allowed as a maximum), it is possible to either manually
set the base to be used, or leave the handset to automatically search for the first available base among those where it had been
previously registered on. Press MENU > HANDSET > SELECT BASE.
The bases where the handset is already registered at will appear on the list.
Select the desired base and confirm by pressing OK, or choose the "AUTOMATIC" option.

16 Settings of the base

How to deactivate a handset associated to the TULIP base

Press MENU > BASE > DEREGISTRATION > OK.
Insert the PIN of the base (e.g. 0000) and select the handset to be deactivated using the
The deactivated handset, if registered also on another base, will automatically start operating under the latter one.
NOTE: it is not possible to deactivate an handset when it is the only one registered on the connected

Flash Time

Press MENU > BASE > FLASH TIME.
Using the

How to modify the PIN of the Base

Press MENU > BASE > PIN BASE > OK.
Insert the PIN of the base (e.g. 0000). Insert the new PIN (4 digits) and confirm by pressing SAVE.
Resetting the Base
NOTE: after the "Base Reset" operation, further to all settings related to the base (chapter 6), all handsets associated with that
base will also be de-registered, with the exception of the original one.
Press MENU > BASE > SET DEFAULT > OK. Insert the PIN of the base (e.g. 0000). The system will ask "Reset all settings ?".
Confirm by pressing the function key OK. After reset has been performed the display will display a notification message.
10
tto_guida_22072011_v.indd 20
keys, select the value for the flash time (from 98ms to 900ms) and confirm by pressing OK.
key on HANDSET 1;
keys, then press OK.
base.
User Manual mod.
25/07/2011 11:12