Publicité
DS-D100IMWF
E N G L I S H
Diagram References
Appearance
1
1
2
3
Display Screen
Microphone
Debugging Port
4
Network Interface
5
Loudspeaker
6
TF Card Slot
7
Alarm Terminal
8
Power Terminal
Note: The debugging port is used for debugging only.
Wiring
2
reserved pins, 4 relay outputs, 8 alarm input pins, and 1 GND pin.
3
onto the wall.
(depth).
Before you begin:
are included.
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
1. Insert 2 expansion tubes into the wall.
4
1
you can use the device.
2. Create a password and confirm it.
Note: We highly recommend you to create a strong password of your own choosing (using
a minimum of 8 characters, including at least three kinds of following categories: upper
security of your product. And we recommend you reset your password regularly,
2
1. Choose Language and tap Next.
2. Set network parameters and tap Next.
- Edit Local IP, Subnet Mask and Gateway parameters.
b. Edit Floor and Room No.
same LAN, the device will be displayed in the list. Tap the device or enter the serial
No. to link.
1
3
60±0.1 mm
32 mm
2.3 mm
53.5±0.15 mm
61±0.1 mm
84.85±0.1 mm
Warnings
required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the device.
● When the product is installed on wall or ceiling, the device shall be firmly fixed.
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please
contact the service center.
disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or
maintenance.)
● The device cover for indoor use shall be kept from rain and moisture.
(ignorance can cause fire danger).
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a
● Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the
detergents.
3
4
1
2
6
7
8
3.5 mm
Lock Catch
Lock Catch
1 mm
Lock Catch
Lock Catch
Rear Panel (without Interface)
Consignes de sécurité
valeur exigée.
● Ne branchez pas plusieurs appareils sur un même adaptateur ; toute surcharge de l'adaptateur pouvant entraîner
sa surchauffe ou provoquer un incendie.
● Si l'appareil dégage de la fumée ou une odeur suspecte, ou s'il émet des bruits inhabituels, éteignez-le et
aucun cas essayer de démonter le produit vous-même. (Nous déclinons toute responsabilité en cas de problèmes
intensité. Évitez d'installer l'équipement sur des surfaces vibrantes ou à des emplacements subissant des chocs
fréquents (au risque de l'endommager).
source de chaleur telle qu'une chaudière ou un radiateur (au risque de provoquer un incendie).
● N'orientez pas l'appareil vers le soleil ou des sources de lumière très vive. Dans le cas contraire, un voile ou des
également être affectée.
des doigts pouvant éroder le revêtement du capot de l'appareil.
pas de détergents alcalins.
● Conservez tous les emballages ; ils pourront vous resservir ultérieurement. En cas de panne, renvoyez l'appareil à
l'usine dans son emballage d'origine. Si l'appareil est transporté hors de son emballage d'origine, il risque d'être abîmé,
entraînant des frais supplémentaires.
2
Red
RS-485+
Red
RS-485-
Blue
Green
Yellow
Yellow
White
Black
NO2
Red
COM2
5
Black
NO1
Black
COM1
Black
AIN8
Black
AIN7
White
AIN6
White
AIN5
White
AIN4
White
AIN3
White
AIN2
White
AIN1
White
GND
Hook
Hook
Hook
Hook
Screw
©2019 Hangzhou Hikvision Digital Technology Co., Ltd.
user license agreement covering that Product.
About this Manual
Co., Ltd. ("Hikvision") reserves all rights to this manual. This manual cannot be reproduced, changed, translated,
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the
permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN
RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR
OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW.
HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
During the use of device, personal data will be collected, stored and processed. To protect data, the
development of Hikvision devices incorporates privacy by design principles. For example, for device with facial
only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable
RS-485
RES
RES
RES
Reserved
RES
RES
Relay Output
Alarm
Input
Device
Wall
Publicité
