Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 60817F
Wrenches: 14mm, 16mm, 17mm, 5/8"
Drill Bits: None
Tie-Down Bracket
Exhaust Mounting
Bracket
1
Qty. (1)
Hex Bolt 7/16 or M10
2
Qty. (8)
Flat Washer 7/16
1.
If present, lower carbon canister and bracket from passenger side of frame.
2.
Remove tie-down brackets from vehicle frame.
3.
Remove exhaust mounting bracket from vehicle frame. (Return tie-down brackets, exhaust Mounting bracket & exhaust mounting
fastener to vehicle owner for reinstallation if hitch Is removed.)
4.
Bolt hitch to vehicle using existing fasteners as shown. Push hitch toward driver's side and tighten all fasteners to torque as listed.
5.
Bolt rubber exhaust hanger to hitch side bracket using fasteners provided as shown.
6.
Reattach carbon canister and bracket to vehicle.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
SAAB 9-2X
FASCIA
Drawbar Kit:
6803
Drawbar must be used in the
RISE position only.
Existing Weldnut
Frame
3
4
Tighten all 7/16" or M10 fasteners until Lock Washer is flat.
Tighten all M12 fasteners with torque wrench to 68 Lb.-Ft.
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB Max Gross Trailer Weight
200 LB Max Tongue Weight
Wiring Access Location: PC1, PC2
Carbon
Canister
Bracket
Push hitch toward drivers side.
Qty. (1)
Lock Washer 7/16
Qty. (1)
Nut 7/16 or M10
24758N
Part Numbers:
24758
77134
60817
Tie-Down Bracket
Existing M12 Bolts
9-28-05
Rev. B
Publicité
Manuels Connexes pour Cequent Towing Products SAAB 9-2X
Sommaire des Matières pour Cequent Towing Products SAAB 9-2X
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24758N 9-28-05 Rev. B 2005 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24758N 9-28-05 Rev. B 2005 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 24758N 9-28-05 Rev. B 2005 Cequent Towing Products...