Cleaning And Maintenance - Bimar Calidea S314 Notice D'instructions

Fax +32 030 9904733
2) Turn the thermostat knob clockwise to the position corresponding to the desired temperature:
3) To switch the appliance on, turn the selector knob (D) to the position corresponding to the
desired function.
4) If desired, select the "TURN"(A) and ionizing"IONIC" (B) functions using the buttons.
5) To turn the appliance off, rotate the knob to position "0" and take the plug out of the socket.
Never leave the appliance connected to the socket if it is not in use, especially for long periods.
Mod. S315 with 24 hour programmer (Fig.2)
The appliance has a switch, a thermostat and a 24 hour programmer, Ionising function and left-right
oscillation. The functions of the switch and thermostat are described in the previous paragraph; the
programmer permits fan heater "on" and "off" periods to be set during a 24 hour period, and of
repeating them systematically, day-after-day.
The programmer is active when the button (F) on its side is aligned with the " " symbol; if it is
aligned with the "I" symbol, the programmer is excluded.
To use the fan heater, act as described in points 1 and 2 of the previous paragraph. Also:
a) Operating with the programmer excluded (button pos. "I").
a1) Turn the switch to line up with position "I" or "I I"; the appliance comes on as does the luminous
pilot light.
a2) To switch off the appliance, turn the switch to pos. "0" (the pilot light goes out) and remove the
plug from the current socket.
b) Operating with the programmer (button pos.
b1) Set the right time: rotate the disc of the timer in the direction shown by the arrow meeting the
right time with the reference dial.
b2) The on/off functions are regulated by small buttons on the crown: if directed inwards, the
appliance remains switched off – if directed outwards it switches on. Push the button in one way or
another (1 button corresponds to 30 minutes).
Adjust the position of the buttons to the times you want the fan heater on (button to the outside) or off
(button to the centre): at this point, segments corresponding to the on and off periods are visible under
the crown.
The programmer will repeat the same functions until they are modified or until the button remains in
the " " position.
b3) If desired, select the "TURN"(A) and ionizing"IONIC" (B) functions using the buttons.
b4) To switch off the fan heater definitively, bring the button to "I", rotate the selector to the "0" and
take the plug out of the socket.
Never leave the appliance connected to the socket if it is not in use, especially for long periods.

CLEANING AND MAINTENANCE

Attention: before cleaning the appliance, turn it off, remove the plug from the outlet and wait for it to
cool.
• Periodically check that the air-intake grill is not obstructed by fuzz or threads.
• Use a soft, slightly damp cloth to clean the body; do not use metal scouring pads or abrasive
products.
• To clean and maintain of the grid, it is possible vacuum cleaner paying attention not to damage the
electrical resistance.
• A special tool is required to replace the electrical cord: contact an authorized service center, also
for any repairs.
• When the appliance is not being used, cover it and put it in a dry place. it is a good idea to put it
back in its original packaging to protect it from dust and humidity.
• If you decide not to use the fan heater, we recommend that you make it inoperative by cutting the
power cord (but first make sure you have removed the plug from the electrical outlet), and make
those parts harmless that are dangerous when played with by children.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
).
9 20
/
Assembly page 9/20