Bimar Calidea S314 Notice D'instructions page 8

Fax +32 030 9904733
• Before connecting the appliance, check that the voltage shown on the data plate matches that of
your electricity and that the electric plug is grounded (230V~ 50Hz). In the event of incompatibility
between the electric outlet and the plug of the heater, have the outlet replaced with another more
suitable type by professionally qualified personnel, who will make sure that the section of the wires
of the outlet is appropriate for the absorbed power of the heater (10A). In general, the use of
adapters or extension cords is not recommended; if their use is indispensable, they must conform to
existing safety standards and their current capacity (amperes) must not be less that the maximum of
the heater.
Attention: before use the appliance remove the detachable coupon to stick the handle.
• Before each use, verify that the heater is in good condition and that the electrical cord is not
damaged: in the case of doubt, ask for professionally qualified help.
• Make sure that the cable is correctly positioned and that it is not in contact with hot parts or sharp
edges, nor wrapped around the device or twisted.
• The power socket must be easy to reach so the plug can be removed quickly in case of emergency.
• Position the fan heater far from other sources of heat, inflammable materials (curtains, carpets,
etc.), inflammable gases or explosive materials (spray cans) and from materials that can deform on
exposure to heat. Make sure that there is 100 cm of free space in front of the fan heater and 30 cm
on the sides. Do not use the heater in the immediate vicinity of a bathtub, shower or swimming
pool (to avoid drops of water falling on the heater or the heater falling in the water), or in places
where it could be subject to shocks.
• Don't hang it on the wall.
• Make sure that the fan heater is working correctly: if not, turn the heater off and have it checked by
professionally qualified personnel.
• Make sure that the air-intake grid is not obstructed by objects, fabrics or anything else to avoid the
heater overheating or breaking.
• Do not use the appliance with a timer or a programmer or with a system that can switch on the
appliance automatically, to avoid risk of fire, since a fire risk exists if the heater is covered or
positioned incorrectly.
• In the case of a breakdown or fault, switch off the appliance and have it checked by a
professionally qualified technician; repairs made by unqualified persons can be dangerous and
render void the warranty.
USE
Before each use, verify that the unit is in good condition, the electric cord is not damaged, if the
power cord is damaged, it must be replaced by the manufacturer or a competent qualified electrician
or a person with similar qualifications, in order to avoid any risk.
mod. S314 basic version (Fig.1)
The fan-heater is fitted with switch, thermostat, Ionising function and left-right oscillation:
- the switch sets following functions:
"0"= OFF; " "= fan; "I"= = air warm (1000W); "I I"= air very hot (2000W)
- the thermostat sets the room temperature, that will be higher if the knob is rotated to position max
clockwise: when the temperature is reached, it will be kept uniform
- Ionising function: this produces a flow of negative ions which neutralise the positive ions in the air;
the ionising function is less evident in environments with high levels of humidity, this fuction is On
then is selected the button (B)
- left-right oscillation: switch on the key for the swinging (TURN) to let the stove swing to the left
and to the right.
To use the thermofan, please follow the instructions below:
1) Insert the plug in the current socket: the pilot light on, comes on indicating the presence of
voltage.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
8 20
/
Assembly page 8/20