Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Page 6 of 9
•
Carefully remove the wiring taking note of its routing.
•
Carefully remove the original licence plate bracket while feeding all the wires through the
holes in the under-tray.
To Remove original indicators
•
Remove the two bolts arrowed in picture 12 and remove the licence plate bolt bracket.
•
Remove the nut arrowed in picture 13 and remove the reflector.
•
Remove the three bolts arrowed in picture 14, the bracket can now be carefully separated
into two halves.
•
Remove the screw arrowed in picture 15 and then the clamp plate and the spreader plate.
•
Then squeeze the rubber indicator stem to allow the indicator to be removed as shown in
picture 16.
•
Repeat the above to remove the other indicator.
To Fit Mini indicators
•
Fit the indicators of choice to the original indicator/licence plate bracket (R&G mini indicator
product code RG371 for LED type or RG372 for Aero Style led type) using the four indicator
adaptors (item 1) as explained below.
•
Pass the indicator wiring through the hole in the rear indicator adaptor (item 1) from the
flat side, then place this assembly into the indicator aperture and place one of the
remaining indicator adaptors (item 1) so the spigot fits into the aperture and secure in
position using the M8 nut.
•
Repeat the above steps on the other indicator.
•
Route the wiring as original.
•
Reassemble the indicator/licence plate bracket as original and remount as original.
•
Reconnect the indicators using the supplied wiring connectors (item 2) into the loom to
check at this stage (if illumination fails, swap the bullet connections around). It is a good
idea at this point to turn the ignition on and check for the correct operation of all lights.
•
Refit both seats.
•
Depending on local laws, attach the enclosed red reflector (item 15) in an appropriate
location.
Please test the indicators, rear light and licence plate illuminator before riding.
•
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation
or warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer
confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or
undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed.
The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective
Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified
or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises
from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or
service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion
of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of
purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy
does not affect your statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1
19/05/2020
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G
(NSY)
www.rg-racing.com
Email:
RAP0011
info@rg-racing.com
Publicité
Table des Matières
