Cequent Performance Products 75712 Instructions D'installation

2007-2010 Patriot bumper
fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75712F
Wrenches: 22mm, 16mm-tow hook option
Drill Bits: 5/8"- Only needed to reinstall
tow hook on Patriot with optional tow hook.
Cutting Tool: Needed to trim
bumper fascia on Compass Rallye and
2011 & later Patriot and Compass.
Note 1.
Patriot with optional tow hook
On Jeep Patriot with optional tow
hook on Driver's side it is
necessary to remove tow hook.
Check with vehicle owner
to see if they want tow hook
reinstalled. To reinstall hook it is
necessary to press/drive existing
knurled neck bolts out of hook
and drill out with 5/8" drill.
Reinstall hook by using supplied
M14 bolts following steps below.
1
Qty. (4) M14 x 120 x 2 Hex Bolt
2
Qty. (2) 5/8" Lock Washer
NOTE: Lowering exhaust may ease installation. To lower exhaust, remove rubber hanger from hanger bracket. Spraying a lubricant or soapy water
on the metal hanger rod and the rubber isolator helps removal. Some vehicles have a carbon canister installed on the driver side frame rail. The
canister, if needed can be lowered allowing for additional clearance during the install.
NOTE: If vehicle has optional tow hook see Note 1. above.
2007-10 Models: Only Rallye edition require fascia trimming
Compass Rallye: see Note 2 and Figure 2.
Jeep Patriot and Compass models 2011 and later. Fascia trimming is required for hitch installation. See Figure 3 and Figure 4 for fascia trimming
Obtain vehicle owners approval before cutting.
** 2011 model has 2" vertical fascia trim (measured from the bottom of the fascia lip). Mark fascia with non-permanent marker. Re-confirm fascia cut height by using figure
4 procedure and mark height from ground on fascia. Cut the lower of the two marks.
To confirm if vehicle requires trimming raise hitch into position between frame rails and mark area that needs to be trimmed.
1.Place M14 hex bolts into vehicle bushings from the outboard side of the vehicle frame rails. Leave bolt ends flush with the inboard side of frame rails.
2.Raise hitch into position and push M14 hex bolts through hitch frame brackets to support the hitch.
3.Attach remaining hardware as shown above.
4.On Compass Rallye Package only. Use hitch receiver tube as a guide to cut a 2-1/4" wide by 2" high piece out of bumper fascia to allow clearance for ball mounts. See
Figure 2.
5. Raise exhaust back into position if lowered prior to hitch installation.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water
and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection.
Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©
2010, 2011, 2011, 2014, 2015 Cequent Performance Products –
Installation Instructions
Jeep Compass*,
Jeep Patriot*,
*2011 and Later Jeep Patriot and Compass models
require fascia trimming for hitch installation. Obtain
Optional tow
vehicle owner approval before cutting.
hook
Rallye Bumper
fascia
2011 & Later Patriot and
Compass fascia To be trimmed.
Vehicle frame
bushing typical
Vehicle may be
installed with a
carbon canister
in this location
Optional tow hook
Reattach existing 10mm
bolt to bumper
Tighten all M14-2 fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Printed in México
Rallye Package
inc.
optional tow hook
inc.
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Vehicle frame
Rail
1
3
4
1
2
4
3
Qty. (2) 5/8" Conical Washer
4
Qty. (4) M14 x 2.0 hex Nut
Sheet 1 of 6 75712N
Part Number:
75712
87606
44661
Max Gross Max Tongue
Trailer WT (LB) WT (LB)
Do NOT Use With Spring Bars
3500 (1 589 Kg) 525 (238 Kg)
Figure 1
diagrams.
2-14-17
Form: F205 Rev A 5-6-05
Rev. K