Maintenance; Carbon Brushes; Service Information; Storage - Manupro MPSCST255MM2 Guide D'utilisation

13. Maintenance

m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
13.1 General maintenance measures
• Keep the safety devices, air vents and motor hous-
ing as free of dust and dirt as possible. Wipe the
device off with a clean cloth or blow it out with com-
pressed air at a low pressure.
• We recommend that you clean the device immedi-
ately after every use.
• Clean the device regularly with a damp cloth and
some soft soap. Do not use any detergents or sol-
vents; these might attack the plastic parts of the
device. Make sure that no water can get into the
interior of the device.
• Oil the moving parts once a month in order to ex-
tend the tool life. Do not oil the motor.
13.1.1 Cleaning the product and saw blade guard
ATTENTION
Product damage due to insufficient cleaning
- Clean the product thoroughly after each use.
ATTENTION
Product damage due to aggressive solvents or clean-
ing agents.
- Use a brush to remove course dirt.
- Clean the product with a damp, clean, lint-free
cloth and soft soap.
1. Remove dust and chips with a brush after each
working operation.
2. Clean the ventilation holes with a lint-free cloth.
13.1.2 Clean the product with compressed air
ATTENTION
Product damage due to use of a compressed air de-
vice with too high of a pressure
By cleaning the product with highly compressed air,
electrical components may become damaged.
- Use a compressed air device with a low pres-
sure of max. 2 bar.
1. Always keep enough distance to the product.
2. Remove dirt with a compressed air device
(max. 2 bar).
13.1.3 Cleaning the chip extraction system
A chip extraction system is not included in the scope
of delivery. Follow the manufacturer's operating in-
structions to properly clean the extraction system.
13.2 Replacing the table insert (Fig. 13)
m WARNING: In case of wear or damage, the table
insert (5) must be replaced; otherwise there is an in-
creased risk of injury.
1. Use a Phillips screwdriver (not supplied) to re-
move the two countersunk screws of the table
insert (25).
2. Remove the worn table insert (5).
3. Installation of the new table insert (5) takes place
in reverse order.

13.3 Carbon brushes

If excessive sparks are generated, have an electri-
cian check the carbon brushes. Attention! The car-
bon brushes must only be replaced by an electrician.

13.4 Service information

Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brush, saw blade, table inserts,
push stick
* Not necessarily included in the scope of delivery!

14. Storage

Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.

15. Electrical connection

The installed electric motor is connected ready
for operation. The connection complies with the
relevant VDE and DIN regulations. The custom-
er's network connection and any extension cable
used must comply with these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection condi-
tions. This means that its use at freely selectable
connection points is not permitted.
• If the network conditions are unfavourable, the de-
vice may result in temporary voltage luctuations.The
product is intended for use only in properties which
a) do not exceed a maximum permissible mains im-
pedance "Z" (Zmax = 0.429 Ω), or
b) w hich have a continuous current carrying capac-
ity of the network of at least 100 A per phase.
• As a user, you must ensure, if necessary in consul-
tation with your power supply company, that your
connection point at which you wish to operate the
product meets one of the two mentioned require-
ments a) or b).
GB | 41