Cequent Performance Products 65054 Instructions D'installation

Trim this air dam
Truck frame
Lower air dam
Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: 65054F
Wrenches: 3/4", 7/8", 15/16"
Drill Bits: None
Other Tools: Tape, Cutting
t l f tool for hard plastic fascia. h d l ti f
Tape 1/2" flat washer in to
depression around hole on outside of
frame both sides of truck.
This is a magnified
9
view of a Bolt Leader
1
Qty. (2) Hex Bolt, 1/2"-13 x 6" Gr5
2
Qty. (2) Flat Washer, 1/2"
3 Qty. (4) Conical Washer, 1/2"
Qty. (2) Hex Nut, 1/2"
4
1. It is necessary to trim a section out of the plastic air dam attached to bottom of bumper. See Picture above.
CONSULT VEHICLE OWNER BEFORE TRIMMING OR CUTTING PLASTIC AIR DAM.`
2. Locate 1/2" flat washers on outside of truck frame rails using tape to secure them as shown in picture above.
3. Insert 1/2" x 6" long bolts through conical washers and spacer tubes and then install through 1" diameter holes on inside of truck frame
rails. Tubes must rest on surfaces of hole both sides of frame. Be careful not to push off washer taped to outside of rails installed in
Step 2. Gently pull bolts back so that end of bolts are even with washers. This is so hitch can be raised into position.
3. Position hitch and raise into position being careful not to knock off taped washers on frame. Install fasteners as shown above.
4. Use 5/8" bolt leaders to pull 5/8" carriage bolts into frame slots and through hitch. Square shoulders of bolts must be pulled out to
engage with sides of frame slots. Use access slots on inside of truck frame as shown above to pull 5/8" carriage bolts through. It may
be necessary to file slots slightly on some truck frames to allow bolts to pass through more easily. Or you can pull bolts through end of be necessary to file slots slightly on some truck frames to allow bolts to pass through more easily Or you can pull bolts through end of
frame above recovery eyes on 4WD models. Torque fasteners to specifications below.
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-M).
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-
5 and SAE J684.
2010 Cequent Performance Products
z
Ford F-150, 2WD & 4WD Models
All including XL, XLT, STX, FX2, FX4, Lariat,
King Ranch, Platinum,*SVT Raptor & **Harley-Davidson
* Raptor requires front skid-shield modification.
** **
H l Harley-Davidson versions may push up on plastic air- dam.
Dimensions for cutting of truck
front plastic air-dam
i
Cut out a piece 1-3/8" up from bottom
of plastic air-dam by 3-1/2" wide for
4WD trucks. 1" up from bottom by
3-1/2" wide for 2WD trucks.
8 7
4 3
Front Mounted Receiver
Installation Instructions
D id i
Lincoln Mark LT – Mexico only
^ All 4 WD trucks come standard with recovery eyes,
2WD model trucks do not. See additional instructions. 2WD model trucks do not See additional instructions
2 2 6 6
5 Qty. (2)
6 Qty. (2)
7 Qty. (2)
Qty. (2)
8
Tighten all 5/8" GR5 fasteners with torque wrench to 150 Lb.-Ft (203 N-M).
Sheet 1 of 3
h l ti i d
CARGO CAPACITY – Do not exceed
500 LB. or Truck Front
Gross Axle Weight Rating, (GAWR).
9,000lb.
^MAXIMUM WINCH LINE PULL
8 7
9 9
1 1 3 3 5 5
Fasteners typical both sides of vehicle
Tube, Spacer x 4-1/4"
Carriage Bolt, 5/8"-11 X 2" Gr5
Conical Washer, 5/8"
Hex Nut, 5/8"
65054N 4-10-10
Part Numbers:
65054
4 4
3
Optional to pull
carriage bolts from
end of frame on
4WD trucks.
Rev. A