Publicité
Les langues disponibles
Les langues disponibles
BODY HARNESS:
• Starting underneath on the driver's side locate and connect the Black/Blue/Red wires from
the jacketed cable to the module's black box using the supplied Perma seal butt connectors.
(See wiring detail for reference.)
WARNING If routing the wire thru a grommet and along the exterior of the vehicle, be
careful to avoid any hot pipes, heat shields, the fuel tank or any other points that may pinch
or break the wire.
• Route the body harness down the driver's side of the vehicle and up into the engine
compartment to the battery location.
• Connect the black wire to the fuse holder Labeled (7-Way harness power fuse) using the
supplied yellow Perma seal Butt connector. Connect ring terminal on the opposite end of the
fuse holder (Wiring Detail on Page 1).
BRAKE CONTROL HARNESS:
• Determine a suitable mounting point on the tow
vehicle for the Electric Brake control
harness.
Note: Brake Control not included. Brake Control
Harness designed to work with Tekonsha® Brake
Controls such as: 90195, 90885 or 90160. Go to
www.tekonsha.com for more details or where
to buy.
• Route the Blue wire from the body harness
through a Grommet in the fire wall. Connect
the blue wire from the body harness to the
blue wire from the brake control harness using
supplied butt connector.
a
• Secure any loose wires or panels from the brake
A
control harness installation.
7-WAY HARNESS:
• Determine 7-Way mounting location.
• Route the 7-Way Harness containing the 7 wires behind rear bumper fascia and over
bumper support bracket, towards the Mounting location.
COMPLETION:
• Secure harness with the cable ties provided, to prevent damage or rattling. Be careful to
avoid any areas that would pinch, cut or melt the wire.
• Apply heat directly to butt connectors, working from the center out to the edges, using a
hot air gun or other source, until the tubing recovers and the adhesive flows. Allow to cool
before inspecting splice and checking integrity.
• Replace all coverings, grommets or any other components that were removed for ease of
installation. Some grommets will need to be altered to allow wires to pass through. Seal
altered grommets with silicone.
• Reconnect the vehicle's Negative (-) battery cable.
• Test and verify installation with a test light or trailer once installed.
TROUBLE SHOOTING GUIDE:
7-Way not function-
Ensure T-One® T-Connector ends are fully inserted and locked in
ing properly
place. Remove Tow Harness power Module 25 amp fuse for 10
seconds and repeat test.
No Power to 7-Way
Installation may have activated circuit protection. Start vehicle and
turn all functions off: Tail (head lights), brake and turns. Remove Tow
Harness power Module 25 amp fuse for 10 seconds and repeat test.
Contact a Tekonsha® approved installer for a professional installation! http://www.tekonsha.com
STILL HAVING TROUBLES?
Just enter you zip code in Where to buy.
• Locate the vehicle's intergraded
brake control harness to the right
of the brake pedal under the
dashboard.
b
• Insert the brake control harness
into the vehicle's mating connector.
b
• Using wire insertion detail, pin 7-Way Connector.
• Connect 7-Way connector and 7-Way socket. Mount 7-Way (Bracket not included).
Check chassis grounds. Ensure ring terminals are in full contact with vehicle's chassis. Remove
Tow Harness power Module 25 amp fuse for 10 seconds and repeat test.
Ensure 25 amp fuse is fully inserted into fuse holder. Fuse should have no breaks. Fuse holder
connected properly to positive post of battery. Remove 25 amp fuse for 10 seconds and re-
peat test. Ensure module is connected to B+. Using a tester or volt meter check for voltage on
either side of the yellow butt connector near the module. Remove Tow Harness power Module
25 amp fuse for 10 seconds and repeat test.
Page 3
FRANÇAIS •
ESPAÑOL
APERÇU DE LA QUINCAILLERIE / REPASO DE LAS PIEZAS:
Attache de câble, 8.5 po (24)
Attache de câble, 14.5 po (1)
Amarre de cable 8.5" (24)
Amarre de cable 14.5" (1)
Ruban double-face (1)
Porte-fusibl (2)
Cinta de dos caras (1)
Portador de fusibles (2)
OUTILS REQUIS / HERRAMIENTAS NECESSARIAS:
Tournevis Phillips #2
Cortadores de cable
Destornillador de estrella (Philips) #2
Soufflerie d'air chaud
Outils à dénuder/Sertisseurs
Soplador de aire caliente
Pelacables/ Plegadores de cable
DÉTAILS DU CÂBLAGE /
DETALLES DEL CABLEADO
MODULITE®
MODULE®
MÓDULO®
VERT / ROUGE
MISE À LA TERRE DU CHÂSSIS
VERDE/ ROJO
CONECTOR A TIERRA DEL
CHASIS
FAISCEAU DE CARROSSERIE
JAUNE / BRUN / BLEU
ARNÉS DE LA CARROCERÍA
AZUL / MARRÓN /
AZUL
ROUGE/NOIR
ROJO/NEGRO
ROUGE/ROJO, 12 GA
CONNECTEUR
T-ONE®
CONECTOR
T-ONE®
BRANCHER SUR LE FEU COMBINÉ ARRIÈRE CÔTÉ PASSAGER
CONECTAR A LA LUZ TRASERA DE COMBINACIÓN DEL LADO DEL PASAJERO
JAUNE/AMARILLO
MARCHE ARRIÈRE/REVERSA
VERT/VERDE
ROUGE/ROJO
GAUCHE / ARRÊT
ARRIÈRE/TRASERAS
IZQ. / FRENO
NOIR/NEGRO
BLANC/BLANCO
BATTERIE +12 V/VERDE
TERRE/TIERRA
7 VOIES CONNECTEUR
BATERÍA DE +12V
7 VÍAS CONECTOR
BRUN/ MARRÓN
BLEU/AZUL
FREINS DE REMORQUE
DROIT / ARRÊT
FRENOS DEL REMOLQUE
DER. / FRENO
CÔTÉ D'INSERTION DU FIL / LADO DE INSERCIÓN DEL CABLE
www.tekonsha.com
Technical Assistance: 800-632-3290
Connecteur d'about jaune (3)
Cosse à anneau (2)
Conector de culata amarilla (3)
Terminal de anillo (2)
Fusible 25 ampères (1), Fusible 30 ampères (1)
Fusible de 25 amperios (1), Fusible de 30 amperios (1)
Coupe-fils
Douille 10 mm
Multimètre ou Voltmètre
Llave de 8mm
Probador o Voltímetro
Clé à cliquet
Extracteur de panneau de garnissage
Trinquete
Retractor de paneles
CONNECTEUR T-ONE®
BRANCHER SUR LE FEU COMBINÉ
ARRIÈRE CÔTÉ CONDUCTEUR
CONECTOR T-ONE®
CONECTAR A LA LUZ TRASERA DE
COMBINACIÓN DEL LADO DEL
CONDUCTOR
FAISCEAU DE COMMANDE DE FREINS /
BLEU
AZUL
ARNÉS DEL CONTROL DEL FRENO
BLEU/AZUL
NOIR/NEGRO
25 AMP
30 AMP
25 A
30 A
VERROU DE FIL
BLOQUEO DE CABLES
TOW HARNESS
7-WAY
POWER MODULE
HARNESS
POWER FUSE
POWER FUSE
25 AMP MAX
30 AMP MAX
PRISE 7 VOIES / CONECTOR DE 7 VÍAS
Page 4
7 Voies Connecteur (1)
7 Vías Conector (1)
Verrou De Fil (1)
Bloqueo De Cables (1)
BATTERIE
BATERÍA
©2022 Horizon Global
Publicité
