Specifications & Technical Data - CABASSE Santorin 30i Notice D'installation

e n g l i s h
Interconnections with the speaker terminals
Connections to the HI LEVEL INPUT
If the preamp section of your Hi-Fi or audio-video system is not
fitted with a lowlevel output, you should then use loudspeaker
cable and connect subwoofer by using its loudspeaker termi-
nals. When connecting the L (left) and R (right) speaker outputs
of your amplifier to the HI LEVEL INPUT
woofer, be careful not to cross (-) and (+) cord of either L (left)
or R (right) channel. Such a phase inversion might damage your
main amplifier.
Connections from the HI LEVEL OUTPUT
The signal from the L (left) and R (right) HI LEVEL OUTPUT
4
plugs is the one being brought in by the HI LEVEL INPUT
connectors.
These outputs can be used to bring the signal to the main loud-
speaker systems or to a second subwoofer in a parallel mono
configuration. In the last lay-out, the L (left) and R (right) HI
4
LEVEL OUTPUT terminals must be connected to the L (left)
5
and R (right) HI LEVEL INPUT
fer. The input signal must then arrive into the first subwoofer by
its L (left) and R (right) HI LEVEL INPUT
Power supply
3
The AC IN cord must be connected to the mains to supply
the subwoofer. The selection of the right voltage 115 V - 230 V
is done with the selector 150 V - 230 V
on ON, then select AUTO or ON on the
With the switch on the AUTO position, the unit will mute after
a few minutes without input signal. The system turns on auto-
matically when signal comes back.
Attention, before operating the unit, be sure that the operating
voltage of your unit is identical with that of your local power vol-
tage.
ADJUSTMENTS
with Baltic with io²
VOLUME VOLUME VOLUME VOLUME VOLUME VOLUME
MIN MAX MIN MAX
MIN MIN MAX MAX MIN MIN
CROSSOVER CROSSOVER
CROSSOVER CROSSOVER CROSSOVER CROSSOVER
40 Hz 200 Hz 40 Hz 200 Hz
40 Hz 40 Hz 200 Hz 200 Hz 40 Hz 40 Hz 200 Hz 200 Hz
CROSSOVER FREQUENCY
This potentiometer adjusts the cut-off frequency which determines
the working bandwidth of the subwoofer. This adjustment should
be done according to the specifications of the main speakers and
the room acoustics. Choose the best frequency after various lis-
tening tests. We have listed above the settings you should start
from for Baltic Evolution, iO2 and Riga.
8
VOLUME
For a first volume adjustment, position the CROSSOVER FRE-
9
QUENCY at around 120 Hz, and turn slowly the volume
8
VOLUME
clockwise from minimum level up to a posi-
tion where you feel that the subwoofer sound level is appro-
priate. A check of the level adjustment will be necessary after
following tests.
All manuals and user guides at all-guides.com
5
plugs
5
plugs of the sub-
4
plugs
5
ones of the second subwoo-
5
terminals.
2
a
. Switch POWER
b
toggle switch.
with Riga
VOLUME VOLUME VOLUME
MIN MAX
MAX MAX MIN MIN MAX MAX
CROSSOVER
CROSSOVER CROSSOVER
40 Hz 200 Hz
40 Hz 40 Hz 200 Hz 200 Hz
9
0
PHASE
For a better sound integration of the subwoofer in the main sys-
0
tem, the PHASE of the subwoofer might have to be inver-
ted (180° position), depending on the distance between the sub-
woofer and the main speakers. You have to check the PHASE
each time you move your speakers and each time you adjust the
9
CROSSOVER FREQUENCY . Attention, if you use 2 sub-
woofers, both phase switches must be on the same position.
SPECIFICATIONS & TECHNICAL DATA
Santorin 30 i
Driver : 30 cm ø - ref 30ND40
Frequency response : 29-200 Hz in semi-reverberating chamber
Maximum sound pressure level : 105 dB RMS
Maximum output power : 400 W RMS
Peak power : 900 W RMS
Lowpass cut-off frequency : Adjustable from 40Hz to 200Hz
Phase inverter : 0° - 180°
Inputs : 2 low level RCA - 2 low level XLR - 2 high level
Power requirements : 115 / 230 VAC - 50 / 60 Hz
Maximum power consumption : 165W
Standby power consumtion :
< 0.5W @ 230VAC --------- 0.4W @ 115VAC
Power consumption when off :
0W @ 230VAC --------------- 0W @ 115VAC
Useable temperature range : +5°C to +35°C
Storage temperature : -5°C to +40°C
Useable humidity range : 40% to 70%
Finish : Glossy black - white
Dimensions ( H x W x D) : 43 x 38 x 47 cm - 19 x 15 x 18.5 in
Weight : 28 kg - 62 lbs
Because of technical improvements already under way in our
constant search for optimum quality, Cabasse reserves the right
to modify all the models presented in specification sheets, adver-
tising materials and manuals without prior notice.
Our web site www.cabasse.com will give you the specific adjust-
ments we recommend for the use of our active subwoofers.
WEEE MARK
Disposal of Wastes of Electrical & Electronic
Equipment (Applicable in the European Union).
This symbol on the product, consisting of the
crossed - out wheeled bin, indicates that this
product shall not be treated as household was-
te. Instead it shall be handed over to the appli-
cable collection point for the disposal of electri-
cal and electronic equipment at the end of life. By
ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to pre-
serve natural resources. For more detailed information about
recycling of this product, please contact your local city office,
your household waste disposal service or the shop where you pur-
chased the product.
0