General Safety Instructions - Dremel 2200 VersaFlame Notice D'utilisation Et Consignes De Sécurité

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 9

GENERAL SAFETY INSTRUCTIONS

GB
Before using the Dremel VersaFlame, make sure you read and
understand this manual completely.
WARNING
!
Failure to follow all instructions listed below may result in ire
and/or serious injury.
SAVE THESE INSTRUCTIONS
a. Keep work area clean and well lit. Cluttered and dark areas
invite accidents.
b. Do not keep combustible materials near the tool.
c. Keep children and bystanders away while operating the tool.
Distractions can cause you to lose control.
d. Only use the tool outdoors or in well-ventilated rooms.
2. PERSONAL SAFETY
a. Stay alert, watch what you are doing and use common
sense when operating the tool. Do not use the tool while
you are tired or under the inluence of drugs, alcohol or
medication. A moment of inattention while operating tools
may result in serious personal injury.
b.
Use safety equipment. Always wear eye
protection. Safety equipment such as a dust
mask, non-slip safety shoes, hard hat and hearing
protection used for relevant conditions will reduce
personal injuries.
c. Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in
unexpected situations.
d. Dress properly. There is a danger of burning yourself with
the lame or with liquid soldering tin. Wear protective
clothing to protect yourself against burns. Keep your hair,
clothing and gloves away from the lame. Loose clothes or
long hair can catch ire.
e. Secure the workpiece. Use a clamping device to hold the
workpiece. This allows you to use both hands to operate the
tool.
f.
Keep this manual for future reference.
g. Do not use the appliance when it is leaking (gas smell),
shows any sign of damage or is malfunctioning.
h. If the appliance is leaking (gas smell) immediately take
it outside and check the leak-tightness without a lame.
Always use soapsuds. (Re)illing the gas tank must be
done in a well-ventilated place far away from any possible
sources of ignition, open lames, pilot lights, electrical
cookware and away from other persons. Be sure to observe
the safety instructions and warning notices on the reill
container. Do not make any modiications to the tool.
i.
Do not work materials containing asbestos (asbestos is
considered carcinogenic).
READ ALL INSTRUCTIONS.
1. WORK AREA
Take protective measures when during work dust can
j.
develop that is harmful to one's health, combustible or
explosive (some dusts are considered carcinogenic); wear
a dust mask and work with dust/ chip extraction when
connectable.
3. TOOL USE AND CARE
a. Store your tool in an appropriate place with an ambient
temperature between 10°C and 50°C. Allow your tool to fully
cool down before storing. Unused tools should be stored away
from children in a dry location. Switch off all unused tools.
b.
Always switch off the tool and allow it
WARNING
!
to fully cool down before attaching or
removing the accessories or before cleaning.
c.
Extremely lammable gas under
WARNING
!
pressure.
d.
Do not use near sparks or an open
WARNING
!
lame.
e.
Do not puncture or incinerate the gas
WARNING
!
tank or store at a temperature above
50ºC.
f.
Keep out of reach of children.
WARNING
!
g.
Do not try to disassemble this unit.
WARNING
!
4. SERVICE
a. Have your tool serviced by a qualiied repair expert using
only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
ENVIRONMENT
DISPOSAL
The tool, accessories and packaging should be sorted for
environment-friendly recycling.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Description . . . . . . . . . . . . . . Dremel VersaFlame
Model number . . . . . . . . . . . 2200
Power source . . . . . . . . . . . . Reined butane gas
Gas tank capacity . . . . . . . . 42 ml / 22 grams
Run time . . . . . . . . . . . . . . . ± 75 minutes (highest setting)
Heat-up time . . . . . . . . . . . . ± 25 seconds (soldering tip)
Nominal heat input . . . . . . . 16 g/h
Cool-down time . . . . . . . . . . 17 min (< 25°C)
Temperature . . . . . . . . . . . . 1200°C (open lame)
Weight . . . . . . . . . . . . . . . . . 227 grams (empty tool)
4
680 – 1000°C (hot air)
550°C (soldering tip)

Publicité

Table des Matières
loading

Table des Matières