Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Always wear SAFETY GLASSES
when installing hitch
Figure 2
Figure 3
℄
4.50"
1.
Remove taillight:
a)
Us i ng flat head screwdriver, remove (1) plastic s crew from taillight cover and remove plastic cover, both sides. Save for rei n stall.
b)
Us i ng 10mm socket, remove (2) nuts from taillight, firmly remove ta illight, and disconnect wiring, both sides. Set aside in safe place for reinstall.
2.
Remove fascia:
a)
Us i ng 8mm socket, remove (1) screw from fascia under taillight, both s ides. Save for reinstall.
b)
Us i ng pry bar, remove (4) plastic ri vets in wheel well trim, both sides. Discard after removal.
c)
Us i ng plastic tri m tool, firmly remove wheel well tri m from (3) cl ips and (2) tree ri vets, both sides. Note: Protect tri m a nd fascia using tape.
d)
Us i ng 8mm socket, remove (2) screws from under wheel well trim, both sides. Save for reinstall.
e)
Us i ng 8mm socket, remove (12) screws from bottom edge of fascia, see Figure 2. Sa ve for reinstall.
f)
Us i ng plastic tri m tools, remove the fascia starting at the outer edges near the wheel wells and gently pull the fascia. Disc onnect the wiring harness from fascia i f present.
3.
Remove heat shield: Us i ng 10mm socket, remove (4) screws from heat shield, see Figure 2. Remove heat shield a nd s et aside in safe place for tri m and reinstall.
4.
Remove impact bar: Us i ng 18mm socket, remove (4) nuts from impact bar. Set aside for reinstall and leave foam s ealant i n place.
5.
Install hitch: Ra i se hitch a nd i mpact bar i nto position aligning holes with studs i n end panel, s ee Figure 1. Note: move wi ri ng near center s ection to s ide. Loosely reinstall the (4)
exi s ting M12 fl ange nuts onto the studs in end panel.
6.
Tighten all hitch fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
7.
Trim heat shield: Us i ng tin snips, tri m area shown in Figure 3.
8.
Rei nstall heat s hield, taillights, wiring, a nd fascia with supplied ri vets ① to wheel well liner.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged
should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cu t access or attachment holes with a torch. This product complies with safety specifications and requirements for
connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
© 2022 Horizon Global ™ Corp. - Printed in Mexico
Installation Instructions
PART NUMBERS: 76923
7.50"
Cut
up to
bend
Existing M12 Flange
Nut (4) Places
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Fasteners
typical
both sides
End
Foam
panel
sealant
Sheet 4 of 12
Fastener Kit: 76923F
①
Qty. (8)
Pl a stic ri vets
②
Qty. (2)
Hex bol t
M12x1.75x100 CL 10.9
③
Qty. (2)
Fl a t washer
7/16"
④
Qty. (2)
Preva i ling torque nut
M12-1.75 CL10
⑤
Qty. (1)
Wa rni ng card
⑥
Qty. (2)
Wa rni ng label
Existing M12-1.50
Stud (4) Places
Figure 1
76923N
05-06-22
Rev. A
Publicité
Table des Matières
