How To Use - Black & Decker Quick 'N Easy Plus FP1445 Mode D'emploi

FP1445Pub1000001798 3/3/05 11:53 AM
Product may vary slightly from what is illustrated.
† 1. Continuous flow side chute
Models FP1445, FP1445C, FP1435 (Part# FP1445-01)
† 2. Continuous flow stopper,
Models FP1445, FP1445C, FP1435 (Part# FP1445-02)
† 3. Food pusher (Part# FP1445-03)
† 4. Food fingers (Part# FP1445-04)
5. Food chute
† 6. Cover with continuous food chute
Models FP1445, FP1445C, FP1435 (Part# FP1445-05 )
Cover without continuous food chute Model FP1335 (Part# FP1335-05)
7. Tab
† 8. Slice/shred disc (Part# FP1445-10)
† 9. Continuous flow discharge disc
Models FP1445, FP1445C, FP1435 (Part# FP1445-06)
†10. Chopping blade (Part# FP1445-07)
11. Hi and Lo speed control
12. Off/Pulse control
13. Center post
14. Base
†15. 8-Cup (1920 ml) container (Part# FP1445-08)
†16. Disc stem (Part# FP1445-09)
†17. Storage lid
Models FP1445, 1445C (Part# FP1445-11)
†Consumer replaceable
Page 4
µ
¸
¹
3

How to Use

This product is for household use only.
• Before first use, unpack the product and remove packing material. Handle
sharp chopping blade and slice/shred disc carefully.
• Wash all parts except base.
Note: Do not attempt to chop ice in this food processor; it will damage container
and dull chopping blade. This unit will not whip cream, beat egg whites to
a desirable volume, grind coffee beans or spices with a high oil content, or slice
or shred hard-cooked eggs, marshmallows, or soft cheeses.
CONTROLS
HI or LO — When these buttons are pressed, unit runs continuously until OFF
button is pressed.
OFF — Processor should always be left in OFF position when unit is not in use.
PULSE — PULSE position must be pressed and held for unit to operate. When
released, unit will stop. Use PULSE for short processing tasks, such as chopping
nuts, raw meats, or vegetables. This lets you check processed results and control
the fineness.
Important: For your protection, this unit has an Interlock system. The processor
won't operate unless container is properly locked onto base (see illustration on
the base). The tab on cover must be correctly locked into the slot on base. Be
sure cover is turned fully into slot toward LOCK until you hear it click into place.
Do not attempt to operate unit without container and cover correctly locked in
place. Be sure base is on a flat, dry, clean surface before you begin processing.
TO SLICE OR SHRED
1. Place container over center post in base with handle at left.
Turn container towards base until it drops down into place.
Snap container in towards base and be sure the locking tab
locks into place (A).
2. To process into a serving/mixing bowl using continuous
flow food chute (Models FP1445, FP1445C, FP1435), place
disc stem onto center post in container (B) and slip the
A
continuous flow discharge disc onto the stem.
Note: Be sure you have the appropriate side of discharge disc
up for leafy or other vegetables. The tabs on the disc should
be up for leafy vegetables.
To process directly into included container, place the disc
stem onto the center post in the container, then grasp the
slice/shred disc by its hub with the (slice or shred) up and
push it down onto the disc stem.
B
3. Place food chute/cover onto container so that its tab is facing down towards
base. Twist food chute/cover in toward base to LOCK until you hear it click
into place.
4. For models FP1445, FP1445C and FP1435 make sure food stopper is in place.
5. Plug cord into an electrical outlet.
6. Fill food chute with food and position the pusher over food.
7. Select HI or LO speed, then press down lightly but firmly on food pusher. For
pulse control push the PULSE button.
4