Publicité

Les langues disponibles

Les langues disponibles

Note: Prior to Assembly
Prior to assembling your cross bar kit check that the kit
contains all the parts you will need to fit the cross bars.
Refer to parts lists for guidance. L-Wrench is stored in the
End Support.
Please read these instructions before assembly.
Step 1: Removing the vehicles anchor point covers.
A.
On the vehicles roof or ditch molding you will find fore and aft
anchor point covers. (fig 1)
B.
Carefully remove these covers by sliding them in the direction
shown on the cover. This will reveal the anchor points. It is
advisable to screw the bolts into the anchor point threads at
this time to clean the threads.
Note: Take care when removing the covers to avoid damaging or
losing clips. Covers will not be replaced while the cross bars are
on the vehicle.
Store the covers and any plugs while cross bars are in use for
later replacement.
Anchor point
cover
Vehicle's roof
Location of anchor points on vehicle
Step 2: Installing Rubber Gaskets and Adaptor
A.
Position the rubber gaskets over the anchor points as
shown in figure. (fig 2)
B.
Ensure that the gasket is properly aligned.
C.
If your gasket and/or adaptor has a directional arrow
ensure this is correctly positioned.
D.
Ensure that the gasket slots are centered over the anchor
point threads in the roof.
E.
Place the plastic adaptors into the gasket's recessed top
surface. (fig 3) Repeat for all four anchor points. (fig 4)
59789N Rev: 10/31/13
Fitting Instructions
2014–ON SOUL WITH ANCHOR POINTS
Crossbar Kit
Anchor point
Fig 1
L-Wrench – Security
Key(2) (Stored in End
Support)
Bolt (4)
Vehicle's roof
Fig 2
Printed in China
PART No:
CARRYING CAPACITY:
Parts list
Cross Bar / End Support
Assembly (2)
Plastic adaptor (4)
Rubber Gasket (4)
Key (4)
Plastic adaptor
Rubber Gasket
Anchor point
Vehicle's
Fig 3
59789
75Kgs/
165 Lbs
roof
Front of vehicle
Fig 4
Pg 1 of 2

Publicité

Table des Matières
loading

Sommaire des Matières pour Rola 59789

  • Page 1 PART No: 59789 Fitting Instructions 75Kgs/ 2014–ON SOUL WITH ANCHOR POINTS CARRYING CAPACITY: Crossbar Kit 165 Lbs Note: Prior to Assembly Parts list Prior to assembling your cross bar kit check that the kit contains all the parts you will need to fit the cross bars.
  • Page 2: Fitting Instructions

    PART No: 59789 Fitting Instructions 75Kgs/ 2014–ON SOUL WITH ANCHOR POINTS CARRYING CAPACITY: Crossbar Kit 165 Lbs Step 3: Fitting Cross Bars to the vehicle (fig 5) Cross Bar Each Cross Bar varies in length. The Cross Bar labeled “FRONT” on the underside of the Cross Bar, belongs to the front location.
  • Page 3: Capacidad De Carga

    59789 Instrucciones Número de parte: 75Kgs / 2014–ON alma SOUL puntos contra Cruz barra CAPACIDAD DE CARGA: Kit de montaje 165 Lbs Nota: Antes de ensamblar Lista de partes Antes de ensamblar el kit de travesaños revise que el kit contenga todas las piezas que se necesitan para ajustar los travesaños.
  • Page 4 59789 Número de parte: Instrucciones 75Kgs / 2014–ON alma SOUL puntos contra Cruz barra CAPACIDAD DE CARGA: Kit de montaje 165 Lbs Paso 3: Instalación de los travesaños en el vehículo (fig 5) Cada travesaño varía en longitud. El travesaño con la etiqueta "FRENTE" en Travesaño...
  • Page 5: Nomenclature Des Pièces

    Instructions de montage No PIÈCE : 59789 2014–ON SOUL AVEC POINTS D'ANCRAGE 75Kgs / Capacité de charge : Traverse de Kit 165 Lbs Nota : Avant le montage Nomenclature des pièces Avant le montage, vérifier que l'ensemble comprend toutes les pièces nécessaires pour installer les traverses.
  • Page 6: Étape 5 : Fermeture Des Capuchons De Supports D'extrémité

    Instructions de montage No PIÈCE : 59789 2014–ON SOUL AVEC POINTS D'ANCRAGE 75Kgs / Capacité de charge : Traverse de Kit 165 Lbs Étape 3 : Pose des traverses sur le véhicule (fig 5) A. Chaque traverse varie en longueur. La traverse étiquetée ‘FRONT’ (Avant) (sur Traverse le dessous de la traverse) ira à...

Table des Matières