Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Part
Description
A
Button head bolt M5 x 35mm
B
Nylon washer
C
Washer-M5
D
Hex nut- locking
E
Screw end protector cap
F
Screw Phillips head M6 x 20mm
G
ROLA cover
H
Direct mount adapter base
I
Brass Nut M6
J
Rubber mounting gasket
K
Hex key- 3mm
L
Silicone sealant
Tools required to install
A
D
E
B
C
Precaution Warnings before beginning
Use of ROLA direct mount system with bolts is intended
for fiberglass top installations.
Install requires drilling and permanent installation of
tracks.
Installation requires some tools and skill. If concerned
please have professionally installed.
Placement of Track Rails onto Vehicle surface (truck shell shown)
Remove covers from adapter
bases if attached.
59753N Rev A
2-11-13
Direct mount System
For use on fiberglass caps
Use with ROLA APE and APX cross bar kits
Qty
8
8
8
8
8
1
4
4
4
4
1
1
A
B
C
C
D
H
E
I
F
Assemble cross bars to desired width
and attach to adapter bases
Printed in China
A
G
B
C
H
D
E
J
Tools required:
Masking tape
Tape measure
8mm wrench
8mm wrench
Fine tip marker
Drill motor
Caution- never exceed the load rating for your
vehicle (contact manufacturer for details), or
that of your cross bar system which ever is
lower.
Align cross bars on vehicle in desired
position. Consider accessory spacing
and potential underside interference
59753
PART No.
50 kgs
Carrying Capacity
110 lbs
F
I
F
Safety glasses
G
Phillips Screw Driver
H
1/8" Drill bit
1/8" Drill bit
I
1/4" Drill bit
CAUTION
Page 1 of 2
L
K

Publicité

loading

Sommaire des Matières pour Rola 59753

  • Page 1 Fine tip marker 1/4" Drill bit Drill motor Precaution Warnings before beginning Use of ROLA direct mount system with bolts is intended CAUTION for fiberglass top installations. Install requires drilling and permanent installation of Caution- never exceed the load rating for your tracks.
  • Page 2 ROLA carries a variety of cross bar styles and lengths to attach to our direct mounting kits. Cross Bars are sold with mounting hardware. Any weight carried on the vehicle will adversely affect its handling particularly in cornering or in a cross wind and the vehicle should therefore be driven with increased caution.
  • Page 3 Système de montage direct PIÈCE Pour utilisation sur capuchons de fibres de verre Utiliser avec les ensembles 50 kg Capacité de de traverses de toit ROLA APE et APX 110 lb charge Qté Pièce Description Boulon à tête ronde M5 x 35mm...
  • Page 4 ROLA offre une variété de styles et de longueurs de traverses de toit à fixer à vos ensembles de montage direct. Les traverses sont vendues avec la visserie de montage. Toute charge transportée par le véhicule affectera la conduite, notamment par effet de dérive ou par vent de côté, de sorte qu'il convient de redoubler de prudence.
  • Page 5 Broca de taladro, 1/4" Motor del taladro Advertencias de precaución antes de comenzar El uso del sistema de montaje directo ROLA está diseñado para PRECAUCIÓN instalaciones en cubiertas de fibra de vidrio. La instalación requiere la perforación y la instalación Precaución: Nunca exceda la capacidad de...
  • Page 6 ROLA vende una variedad de estilos de travesaños y longitudes para instalar con nuestros kits de montaje directo. Los travesaños se venden con accesorios de montaje. Cualquier peso del vehículo afectará de manera adversa su manipulación especialmente en las esquinas o con el viento en contra, por lo cual el vehículo se debe conducir con mayor precaución.