Extension Cords; Electrical Requirements - Bosch 4212 Consignes De Fonctionnement/Sécurité

WARNING
!
"READ ALL INSTRUCTIONS" — Failure to follow the SAFETY RULES identified by BULLET (
ed BELOW and other safety precautions, may result in serious personal injury.
Double insulation is a design concept used in
electric power tools which eliminates the need for the
three wire grounded power cord and grounded power
supply system. It is a recognized and approved sys-
tem by Underwriter's Laboratories, CSA and Federal
OSHA authorities.
Servicing of a tool with double insulation require
G
care and knowledge of the system and should
be performed only by a qualified service techni-
cian.
WHEN SERVICING, USE ONLY IDENTICAL
G
REPLACEMENT PARTS.
POLARIZED PLUGS. Your tool is equipped with
G
a polarized plug (one blade is wider than the
other), this plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the out-
let, reverse the plug. If it still does not fit, contact
a qualified electrician to install the proper outlet.
To reduce the risk of electrical shock, do not
change the plug in any way.
"SAVE THESE INSTRUCTIONS"

Electrical Requirements

1. Connect this saw to a 120V, 15-amp branch cicuit
with a 15-amp time delay fuse or circuit breaker.
Using the wrong size fuse can damage the motor.
2. Fuses may "blow" or circuit breakers may trip
frequently if motor is overloaded. Overloading can
occur if you feed the blade into the workpiece too
rapidly or start and stop too often in a short time.
3. Most motor troubles may be traced to loose or
incorrect connections, overload, low voltage
(such as small size wire in the supply circuit or too
overly long supply circuit wire). Always check the
connections, the load and the supply circuit when-
ever motor does not work well. Electric Brake
Your saw is equipped with an automatic electric brake
which is designed to stop the blade from spinning in
about five (5) seconds after you release the trigger
switch. It is useful when making certain cuts in wood
where a coasting blade would result in a wide, impre-
cise cut.
Safety
Replace damaged cords immediately. Use of
G
damaged cords can shock, burn or electrocute.
If an extension cord is necessary, a cord with
G
adequate size conductors should be used to
prevent excessive voltage drop, loss of power or
overheating. The table shows the correct size to
use, depending on cord length and nameplate
amperage rating of tool. If in doubt, use the next
heavier gauge. Always use U.L. and CSA listed

extension cords.

RECOMMENDED SIZES OF EXTENSION CORDS
Tools
Ampere
Rating
3-6
6-8
8-10
10-12
12-16
NOTE: The smaller the gauge number, the heavier
the cord.
WARNING
!
motor will gradually slow down and the braking action
is initiated ONLY by the release of the trigger switch.
The electric blade brake of your miter saw has been
designed for highest degree of reliability, but unex-
pected circumstances such as contamination on the
commutator and brushes or failure of motor's compo-
nents can cause the brake not to activate. If this con-
dition occurs, turn the saw "ON" and "OFF" four to five
times without contacting the workpiece. If the tool
operates but the brake does not consistently stop the
blade in about five (5) seconds, DO NOT use saw and
have it serviced immediately.
WARNING
!
Remember to let the saw blade come to a complete
stop before raising the blade from the workpiece. As
always the guard system is your best protection
against unintentional contact with a spinning saw
blade. NEVER wedge open or defeat the closing
action of the lower guard.
7.
G
Extension Cords
120 Volt A.C. Tools
Cord Length in Feet
Cord Size in A.W.G.
25 50 100
18 16 16
18 16 14
18 16 14
16 16 14
14 12 N/A
When electrical power is lost due to
blown fuse or other causes, the
The brake action of this saw is not
intended as a safety feature.
) symbol list-
150
14
12
12
12
N/A