Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
6. ELECTROCHEMICAL MARKING
In addition to its use for cleaning and polishing welds, the machine can be used for electrochemical marking of stainless
steel. With this function any logo can be marked instantaneously onto metal (stainless steel). The machine causes stabilized
oxidation of stainless steel that is permanently indelible. The electrochemical process is based on the electrolysis of neutral
solutions, which are neither corrosive or irritant. It is possible to obtain darker and bolder marks positioning the operating
knob (10) working in alternate current (black line) or lighter marks working in direct current (white line).
Pay attention: marking function require the use of a special Kit "Marking Kit" (Pictures C) (composed by electrolytic
solutions, insert and special felts, specific for this function) with a marking screen (40) personalized with
customer logo.
To buy the "Marking Kit" (Picture C) and marking screens you can directly contact N
For further information, please contact: N
Components of "Marking Kit" (Picture C):
Nr. 1
Handgrip (33)
Nr. 1
Torch support (25)
Nr. 1
Torch power cable (31)
Nr. 1
Allen key 2,5mm
6.1. M
ARKING SCREEN
To mark stainless steel surfaces it is necessary the use of a marking screen (40) that it is realizable on specific graphic
request of customer. Please contact N
are: min. 25x15mm - max. 257x170mm. With marking screen is possible to realize approximately 1000 marks, if it is used
correctly. For further information please contact N
N
-G
offers to its customers the possibility to buy a printer, connectable to a PC, in order to print disposable screens
ITTY
RITTY
marking. These screens are specific, for example, to mark serial numbers, logos and EC tags.
For further information contact: N
6.2. M
ARKING GRAPHITE INSERTS INSTALLATION
1. Unscrew the screw (34) situated on the handgrip (33) with the 2,5mm Allen Key.
2. Install the graphite insert (35) on the handgrip (33) and fix it with the 2,5mm Allen Key.
6.3. M
ARKING FELTS INSTALLATION
1. Put the marking felt (36) on the graphite insert (35) so that it will be all covered.
2. Fix the marking felt (36) to the graphite insert (35) using the O-ring (37).
Pay attention: in case the marking felt (36) is not properly fixed the following situations can arise:
short-circuit due to the contact between the graphite insert (35) and the workpiece .
the marking screen (40) can be damaged by the contact with a corner of the graphite insert (35).
6.4. W
-
ORK
PROCESS SELECTION
Put the knob (10) on the marking function you selected (red area)
Black line (AC)
:
for darker and bolder marks (with marking electrolyte - 38)
for lighter marks
White line (DC)
:
6.5. E
LECTRIC INSTALLATION
Machine OFF:
1. See Chapter 3
2. Put the clamp of the ground cable (19) on the stainless steel work piece that has to be marked.
3. Connect one side of the small torch power cable (31) into the socket (5) situated in the front panel of the machine and the
other side on top of the handgrip (33). (Picture L3).
CLINOX POWER
(40)
(P
D)
ICTURE
-G
to buy a personal marking screen. Standard marking screen dimensions
ITTY
RITTY
-G
ITTY
RITTY
-G
(info@nitty-gritty.it).
ITTY
RITTY
(P
ICTURE
(operating knob - 10)
with erosion electrolyte
(
(
)
OPTIONAL
-G
(info@nitty-gritty.it).
ITTY
RITTY
Nr. 1
Marking graphite insert (35a)
Nr. 20 Marking felts (36a)
Nr. 5
O-ring (37a)
Nr. 1
Marking electrolyte100ml (38)
Nr. 1
Erosion electrolyte 100ml (39)
(info@nitty-gritty.it).
(P
L1)
ICTURE
L2)
:
.
- 39).
42
-G
.
ITTY
RITTY
Publicité
Table des Matières
