The Traynor Ycv4050; Introduction; Features; Channel 1 - YORKVILLE Traynor Custom Valve YCV4050 Mode D'emploi

1
Gain Volume
5 5

Input

0 10 0 10
BOOST
YCV4050
120VAC
A-Z356R / 1v1 230V
50Hz 0,5A 60Hz 1.0A
FUSE: T800mA FUSE: T2.0A
sloblo
Send
On
CAUTION:
REPLACE FUSE
WITH SAME TYPE AND RATING
ATTENTION:
REMPLACER LE
FUSIBLE DU MEME TYPE ET DU
MEME COURANT NOMINAL
Power
DISCONNECT POWER
BEFORE SERVICING!
DEBRANCHER L'APPAREIL AVANT
D'ENLEVER LES COUVERCLES!

The Traynor YCV4050

Introduction

The Traynor YCV4050 is a professional all-tube guitar combo. It draws on the rich tradition of Traynor guitar amplifiers
and combines the best of vintage design combined with modern principles, manufacturing techniques, and technology.

Features

• 100% Designed and Manufactured in North America!
• All-tube design with two 6L6 and three 12AX7A Premium tubes.
• A Single 12-inch Celestion® Creamback speaker for great classic sound and performance.
• Using all plywood for the construction of the cabinet guarantees the durability and rigidity that made Traynor famous.
• Separate tone controls on each of the two channels (lead and clean) for flexibility.
• Classic Long-Style Accutronics® Reverb, with dual springs, for authentic vintage sound.
• External speaker jack for the ultimate in versatility.
• Traynor TFS-2B latching dual-footswitch, with 10-foot cable included.
• A special DC powered filament supply on preamp tubes ensures reduced hum.
• Fully regulated power supply ensures ultra low noise.
• The best warranty in the business: a 2-year unlimited, transferable
"even if you break it" warranty (valid in the USA and Canada only).

Channel 1

1. Input
Channel 1 is the lead/overdrive channel and is selected in one of two ways, via the Channel Select switch on the
control panel, or via the Channel Select button on the supplied footswitch* pedal. A Yellow LED located next to the
Channel 1 Volume control illuminates when Channel 1 is active.
*Note: Plugging in the footswitch deactivates the panel-mounted Channel and Boost controls.
2. Gain & Volume Controls
Channel 1 uses a Gain control in conjunction with a Volume control to control the amount of tube-based overdrive
and volume. The Gain control is used to adjust the amount of overdrive, while the Volume control allows you to set
the actual loudness of the amplifier.

3. Boost Switch

A boost circuit is included to help you achieve 'a-bit-more' overdrive for leads. The boost can be selected via the front
panel switch or through the supplied footswitch pedal. A Red LED illuminates to indicate when the boost is active.

4. Channel 1 Tone Controls

The Treble, Bass, and Middle tone controls are used to help you shape your sound. They are post-gain and pre-
volume. These are active only when Channel 1 is selected.
2
Treble Bass Middle Volume
5 5 5
0 10 0 10 0 10 0
Vintage / CHANNEL CHANNEL
Modern SELECT SELECT
SPLITTER PREAMP
12AX7 12AX7 12AX7
V3 V2 V1
Ch. Select
Rtn
/ Boost
POWER
DISCONNECT POWER WHEN
REPLACING TUBES
6L6B 6L6B
DÉBRANCHÉ L'APPAREIL AVANT
DE REMPLACER LES LAMPES V5 V4
Extension
Speaker
EFX / Line Footswitch
DESIGNED & MANUFACTURED BY
YORKVILLE SOUND • Toronto, CANADA
THIS UNIT MUST BE GROUNDED!
CET APPAREIL DOIT ÊTRE MIS À LA TERRE!
1
Treble Bass Middle
5 5 5 5
10 0 10 0 10 0 10
BRIGHTNESS
Custom Custom Valve Custom
TRAYNOR YCV4050 TRAYNOR YCV4050 TR AYNOR YCV4050
Master
Reverb
Volume
5 5
Power
0 10 0 10
STANDBY STANDBY
Valve Valve