Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
– Brush against the fibre direction of the
artificial grass.
– Pull the device towards the user and let
it roll away from the user with the force
of the brush.
– Repeat this movement until the desired
result is achieved.
Always test a small, inconspicuous
piece of artificial grass first to
check that the fibres of the artificial
grass do not come loose.
7. Adjusting the working length
(See Fig. D).
For adjusting the working length of the
7.1
device loosen the sleeve nut (1) by turn-
ing clockwise (right hand threads).
Press the unlock button (8) and pull
7.2
resp. push the tube forth and back.
Release the unlock button in order to
7.3
adjust the length according to you
needs. Let the shaft snap into the clos-
est step.
Secure the shaft by tightening the
7.4
sleeve nut (1) before resuming work.
8. Changing the brush roller
(See Fig. E).
Press the lock/unlock button (10) and
8.1
remove the housing cover (11).
Remove the brush roller (12) from the
8.2
unit.
Insert a new roller intended for the
8.3
device.
Re-attach the cover to the housing and
8.4
press the lock/unlock button (10), so
the housing cover can snap in place.
Make sure the cover is securely locked
in place before resuming work.
9. Usage hints
• If necessary moisten the surface lightly
and use the device like a broom.
• Draw it over the ground in straight lines
and loosen the dirt from the ground.
• Do not keep the rotating brushes in one
place for extended times, the surface
may be marked.
10. Cleaning
• Always pull the power plug before
undertaken maintenance work on the
device.
• If lumps of earth or plants are stuck in
the brush roller while working, first turn
off the device. Start the motor only for a
moment. The blockage will be cleared
by the movement of the brush roller.
• Should it be necessary to loosen the
dirt by hand, first disconnect the power
cord for your safety.
• Use a stiff brush and a dry cloth to
clean the device; do not use aggressive
chemicals or abrasives for cleaning.
• Do not allow liquids of any kind to enter
the device.
11. Storing
• Clean the device before storing it.
• Before storing check all parts and the
power cable for damages.
• Store the device indoors in dry place
that is protected from dust and dirt and
extreme temperatures.
12. Technical data
Operating voltage: . . . . . . . 230 V~ 50 Hz
Nominal power: . . . . . . . . . . . . 1020 W
No load speed: . . . . . . . 800 – 1300 min
Brush roller:. . . . . . . . . . . .20 x 260 mm
Protection standard: . . . . . . . . . . . IP20
Sound pressure level L
Uncertainty K
: . . . . . . . . . . . . 3 dB(A)
pA
Sound power level L
Uncertainty K
: . . . . . . . . . . . . 3 dB(A)
WA
Vibration
Main handle: . . . . . . . . . . . . . a
Uncertainty K: . . . . . . . . . . . . .1.5 m/s
Auxiliary Handle: . . . . . . . . . . . .a
Uncertainty K: . . . . . . . . . . . . .1.5 m/s
Protection class: . . . . . . . . . . . . . . . . II
Dimensions approx.: .129/139 × 35 × 18 cm
Weight: . . . . . . . . . . . . . . . . . . 5.8 kg
* Sound and vibration emissions may differ
from the declared values during use
depending on the ways in which the tool is
used.
English
: . . . . 85.20 dB(A)
pA
: . . . . . 96.20 dB(A)
WA
m/s
h,M
m/s
h,B
-1
2
2
2
2
9
Publicité
Table des Matières
