Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Chemical
alachlor
atrazine
benzene
carbofuran
carbon tetrachloride
chlorobenzene
chloropicrin
2,4-D
dibromochloropropane(DBCP)
o-dichlorobenzene
p-dichlorobenzene
1,2-dichloroethane
1,1-dichloroethylene
cis-1,2-dichloroethylene
trans-1,2-dichloroethylene
1,2-dichloropropane
cis-1,3-dichloropropylene
dinoseb
endrin
ethylbenzene
ethylene dilbromide (EDB)
haloacetonitriles (HAN)
bromochloroacetonitrile
dibromoacetonitrile
dichloroacetonitrile
trichloroacetoritrile
haloketones (HK):
1,1-dichloro-2-propanone
1,1,1-trichloro-2-propanone
heptachlor (H-34,Heptox)
heptachlor epoxide
hexachlorobutadiene
hexachlorocyclopentadiene
lindane
methoxychlor
pentachlorophenol
simazine
styrene
1,1,2,2-tetrachloroethane
tetrachloroethylene
toluene
2,4,5-TP (silvex)
tribromoacetic acid
1,2,4-trichlorobenzene
1,1,1-trichloroethane
1,1,2-trichloroethane
trichloroethylene
trihalomethanes (includes):
chloroform (surrogate chemical)
bromoform
bromodichloromethane
chlorodibromomethane
xylenes (total)
* Chloroform was used as the surrogate chemical for VOC reduction claims
Brondell, Inc
PO Box 470085
San Francisco, CA 94147
www.brondell.com 1-888-542-3355
CORAL UC300 Filtration
System Performance Data Sheet
Drinking Water
Regulatory Level
(MCL/MAC)
(mg/L unless specified)
0.002
0.003
0.005
0.040
0.005
0.100
–
0.070
0.0002
0.600
0.075
0.005
0.007
0.070
0.100
0.005
–
0.007
0.002
0.700
0.00005
–
–
–
–
–
–
0.0004
0.0002
–
0.050
0.0002
0.040
0.001
0.004
0.100
–
0.005
1.000
0.050
–
0.070
0.200
0.005
0.005
0.080
10
1 These harmonized values were agreed upon by representatives of USEPA and Health Canada for the purpose of
evaluating products to the requirements of this Standard.
2 Influent challenge levels are average influent concentrations determined in surrogate qualification testing.
3 Maximum product water level was not observed but was set at the detection limit of the analysis.
4 Maximum product water level is set at a value determined in surrogate qualification testing.
5 Chemical reduction percent and maximum product water level calculated at chloroform 95% breakthrough
point as determined in surrogate qualification testing.
6 The surrogate test results for heptachlor epoxide demonstrated a 98% reduction. These data were used to
calculate an upper occurrence concentration which would produce a maximum product water level at the MCL.
Influent Challenge
Chemical Reduction
Concentration
Percent (%)
(mg/L unless specified)
0.050
> 98
0.100
> 97
0.081
> 99
0.190
> 99
0.078
0.077
> 99
0.015
0.110
0.052
> 99
0.080
> 99
0.040
> 98
0.088
0.083
> 99
0.170
> 99
0.086
> 99
0.080
> 99
0.079
> 99
0.170
0.053
0.088
> 99
0.044
> 99
0.022
0.024
0.0096
0.015
0.0072
0.0082
0.08
> 99
0.0107
6
0.044
> 98
0.060
> 99
0.055
> 99
0.050
> 99
0.096
> 99
0.120
> 97
0.150
> 99
0.081
> 99
0.081
> 99
0.078
> 99
0.270
0.042
> 98
0.160
> 99
0.084
0.150
> 99
0.180
> 99
0.300
0.070
> 99
Maximum Product
Water Concentration
(mg/L unless specified)
0.001
3
0.003
3
0.001
3
0.001
3
98
0.0018
4
0.001
3
99
0.0002
3
98
0.0017
4
0.00002
3
0.001
3
0.001
3
95
0.0048
5
5
0.001
3
0.0005
3
0.001
3
0.001
3
0.001
3
99
0.0002
4
99
0.00059
4
0.001
3
0.00002
3
98
0.0005
3
98
0.0006
3
98
0.0002
3
98
0.0003
3
99
0.0001
3
96
0.0003
3
0.0004
98
0.0002
6
0.001
3
0.000002
3
0.00001
3
0.0001
3
0.001
3
0.004
3
0.0005
3
0.001
3
0.001
3
0.001
3
99
0.0016
4
0.001
3
0.0005
3
95
0.0046
4
0.0005
3
0.0010
3
95
0.015
0.001
3
21
Publicité
Table des Matières
