Toilet Tank Fill Valve Instructions; Important - Toto CST764S Instructions D'installation

TOILET TANK FILL VALVE INSTRUCTIONS

G-Max / E-Max
TM TM
WARNING! DO NOT USE IN-TANK BOWL CLEANERS
The use of high concentration of chlorine or chlorine-related products can
seriously damage fittings in the tank. This damage can cause leakage and
property damage. • TOTO ® shall not be responsible or liable for any tank fit-
ting failure or damage caused by the use of in-tank bowl cleaners.
INSTALLATION
1. Shut OFF water supply to toilet.
2. Flush toilet and remove remaining water from tank with a sponge.
3. Remove the water supply connection at the fill valve.
4. Remove old fill valve and use damp sponge to clean hole in tank.
5. Place new fill valve inside tank hole.
6. Thread mounting nut onto fill valve shank and tighten nut.
Note: DO NOT OVERTIGHTEN. Be sure to install fill valve in a
position that does not interfer with the trip lever operation.
7. Connect water supply to fill valve shank and hand tighten only.
Note: DO NOT OVERTIGHTEN. These are plastic parts.
Never use pipe dope on any water supply connection.
8. Attach refill tube to fill valve nipple and clip other end of refill
tube to the overflow pipe.
9. Turn water supply ON and check for leaks outside the tank.
Note: As water fills the tank, water is also directed into the
overflow tube via the refill tube. This additional flow
of water is critical to refilling your toilet's bowl. Once the
water stops filling the tank, some residual drops of water
may drip from the fill valve. This is NORMAL as these
drops will subside.
WATER LEVEL ADJUSTMENT
Depending on the manufacturing plant, you may have one
or the two of following fill valves.
WATER
LEVEL
Type A Type B
TOTO U.S.A., Inc.
• 1155 Southern Rd, Morrow, GA 30260 Tel. (888) 295-8134 • Fax (800) 699-4889
www.totousa.com Printed in U.S.A. TOTO LTD.
4
For Type A fill valve, allow the water to fill the tank. Adjust
water level as necessary so that water level height inside
tank is 1/2" below the top of the overflow tube. Turn the
adjustment screw clockwise in the (+) direction to increase
the water level height. Turn the adjustment screw counter-
clockwise in the (-) direction to decrease the water level
height. Flush the toilet to verify the correct water level.
Adjust as necessary.
Top of
Overflow Tube
1/2"
(12mm)
For Type B fill valve, there are no water level adjustments.
THE FILL VALVE HAS BEEN PRESET AT THE FACTORY.
The water level height should be 1/2" below the top of the
overflow tube.
Top of
Overflow Tube
1/2"
(12mm)
OPERATION (NOTE TO OWNER)
You have chosen a TOTO ® product that is superior in quality
and craftsmanship. Our toilet flushing systems are the
best in the industry. To insure that your toilet is performing
correctly, always flush the toilet with a full stroke of the
trip lever to activate the flushing cycle. A full stroke will
guarantee that you are flushing with the power of a TOTO ®
If you need advice on your installation or Fill Valve Service
Instructions, feel free to contact one of our Technical
Support members at the number below.
©
I
NSTRUCTIONS D`
Pour Toilettes CST764S(G)/CST774S/CST794SF/CST794EF
Mettez cette notice d`utilisation à la disponibilié des clients. Ces
instructions comprennent des informations relatives à l`entretien.
OUTILS NECESSAIRES:
• Clé à tube de 12" (30,48 cm)
• Clé à molette de 10" (25,40 cm)
• Niveau à bulle d`air
• Mètre à ruband
• Pince
• Tournevis long de 12" (30,48cm)
• Couteau à mastiquer
• Moteur de la perceuse, foret de 11/64
parquet) et foret béton 1/4" (pour installation sur sol en béton
carrelage)
MATERIEL REQUIS:
• Tuyau d`alimentation/ Raccord
• Robinet d`arrêt
• Boulons de montage (2)
• Rondelle en caoutchouc/ Joint
Contenu de l`emballage:
Article Description
1. Cuvette vitrifiée en porcelaine................................. 1
2. Cache.( Pas pour CST794SF/CST794EF)............... 2
3. Ensemble écrous de montage supérieur
(pour le siège)......................................................... 1
4. Robinetterie UNIFIT (TSU01W.12) ..................... 1
4a. Boulon de montage des toilettes (Boulon en T).... 2
4b. Rondelle du boulon en T.......................................... 2
4c. Ecrou du boulon en T............................................... 2
.
4d. Vis de Montage avec Rondelle................................ 4
4e. Ancrage. . . ................................................................. 4
4f. Raccord de Sortie en PVC*.....................................1
Remarque : Due à la puissante performance de nos systèmes de chasse d`eau G-max
qui ne sont pas spécifiés pour une installation Dos-à-dos. La seule façon d`installer ces WC
Dos-à-dos, est lorsque l`égout de connexion du cabinet inclus un élément WYE. Prendre soin de
contacter votre constructeur ou l`entrepreneur avant toute installation.
I
NSTALLATION

IMPORTANT

Lisez attentivement
ces instructions avant
toute installation.
Vous venez de faire
l`aquisition de l`une
des meilleurs toilettes
disponibles sur le
marché actuel,
garanties par la
renommée mondiale
de TOTO ® .
(pour installation sur
"
Vérifiez que
les dimensions
sont correctes
Quantité
*IMPORTANT: La robinetterie
et Power Gravity ,
TM TM
de l`alimentation en eau est
significativement plus large
que la norme de 127mm.
Consultez votre entrepreneur.
REMARQUE: Compensée convenablement
pour le plinthe du mur.
9