Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
INSTALLATION
INSTRUCTIONS
KIT CONTENTS:
TOOLS REQUIRED:
ISOPROPYL
ALCOHOL
*Sealant Adjustment
Isopropyl
Tool Part #:
Alcohol
SOA801AT100
It is strongly recommended that this product be installed by your Subaru Retailer.
NOTE: If installing Body Side Moldings along with Door Edge Guards, the Body Side Moldings must be installed first. This is required for proper positioning of
the two accessories. If the vehicle has Body Side Moldings previously installed and the distance between the edge of the Body Side Molding and edge of the
door is less than 5mm, the Door Edge Guards will not be able to be installed due to spacing issues.
MEANING OF CHARACTERS:
: CAUTION – A process that must be
carefully observed in order to reduce the
risk of damage to the accessory/vehicle
and to ensure a quality installation.
STEP ONE: Prepare the Door's Surface
1a
Before installation, confirm there is sufficient clearance between the door edge and the sealant bead for proper seating of the Door Edge Guard.
SUFFICIENT CLEARANCE
Figure A
To adjust the seam sealer clearance when less than 2 mm exists between the door edge and the seam sealer, align the "green arrow"
on the Sealant Adjustment Tool with the inside of the door's edge. Place the pushing edge in the crease where door sealant bead and
metal meet on the inside of the door (Figure C). Lightly push sealant adjustment tool in order to move sealant for preparation of
install. It is critical that close attention be paid to the first 18mm of the sealant bead going down from the top where the Door Edge
Guard starts and the last 18mm at the bottom where the Door Edge Guard ends for proper Door Edge Guard retention
PART NUMBER:
SOA801P052xx
DESCRIPTION: Forester Wilderness Door Edge Guard
Door Edge Guard 4 pc.
Lint-Free Towel
Scissors
: STOP - Damage to the vehicle may
occur. Do not proceed until process has
been complied with.
CHECK SEALANT IN AREAS INDICATED BY
ONLY USE THE TOOL IN THE AREA THE DOOR EDGE GUARD WILL BE INSTALLED
Looking Down the Door Edge
INSUFFICIENT CLEARANCE
DATE:
ISSUE:
09-14-21
REV. – B
PART NUMBER: SOA801P052xx
Painter's Tape
Paper Installation
Templates (Pages 4 - 7)
GREEN LINE.
Figure B
SUBARU OF AMERICA
*Vaughan 12 oz.
Rubber Mallet
(or any 12 oz. Rubber Mallet)
: TOOLS & EQUIPMENT - Specific Tools
and equipment recommended for this
process.
ADJUSTING
Figure C
PAGE
Nylon
Removal
Tool
1/7
Publicité
Manuels Connexes pour Subaru SOA801P052 Serie
Sommaire des Matières pour Subaru SOA801P052 Serie
- Page 1 (or any 12 oz. Rubber Mallet) It is strongly recommended that this product be installed by your Subaru Retailer. NOTE: If installing Body Side Moldings along with Door Edge Guards, the Body Side Moldings must be installed first. This is required for proper positioning of the two accessories.
- Page 2 EDGE OF THE DOOR. HOLD MALLET AS SHOWN. START !! HOLDING DOOR EDGE GUARD IN PROPER ALIGNMENT WITH ONE HAND, DIRECTLY & DELIBERATELY PERFORM INITIAL STRIKE AT STRIKE POINT #1. PART NUMBER: DATE: PAGE ISSUE: SUBARU OF AMERICA 09-14-21 SOA801P052xx REV. – B...
- Page 3 IN ½” INTERVALS MOVING DOWN OR UP UNTIL ~2” OF DOOR EDGE GUARD IS DISENGAGED. REPEAT THIS PROCESS AT OTHER END. ONCE ~2” OF BOTH TOP AND BOTTOM OF DOOR EDGE GUARD IS DISENGAGED, CONTINUE UP OR DOWN ENTIRE DOOR EDGE GUARD LENGTH UNTIL REMOVAL IS COMPLETE. ISSUE: PART NUMBER: DATE: PAGE SUBARU OF AMERICA REV. – B 09-14-21 SOA801P052xx...
- Page 4 Front Driver Door Template: PART NUMBER: DATE: ISSUE: PAGE SUBARU OF AMERICA REV. – B SOA801P052xx 09-14-21...
- Page 5 Front Passenger Door Template: PART NUMBER: DATE: ISSUE: PAGE SUBARU OF AMERICA REV. – B SOA801P052xx 09-14-21...
- Page 6 Rear Driver Door Template: PART NUMBER: DATE: PAGE ISSUE: SUBARU OF AMERICA REV. – B SOA801P052xx 09-14-21...
- Page 7 Rear Passenger Door Template: PART NUMBER: DATE: PAGE ISSUE: SUBARU OF AMERICA REV. – B SOA801P052xx 09-14-21...
-
Page 8: Outils Requis
12 onces) Il est fortement recommandé de faire installer ce produit par votre concessionnaire Subaru. REMARQUE : Si vous installez les baguettes de flanc avec les bords de portes protégés, les baguettes de flanc doivent être installées en premier. Cela est nécessaire pour un positionnement approprié... - Page 9 POINT DE DÉPART MAINTENIR EN PLACE LA PROTECTION DE BORD DE PORTE AVEC LA MAIN ET FRAPPER DIRECTEMENT ET FERMEMENT AU POINT DE FRAPPE N NUMÉRO DE PIÈCE : DATE : PAGE VERSION: SUBARU OF AMERICA REV. – B 2021-09-14 SOA801P052xx...
- Page 10 QU’UNE PORTION D’ENVIRON 2 PO DU HAUT ET DU BAS EST DÉGAGÉE, CONTINUER À PROCÉDER PAR MOUVEMENT VERTICAL VERS LE HAUT OU VERS LE BAS SUR TOUTE LA LONGUEUR DU PROTECTEUR JUSQU’À SON RETAIT COMPLET. VERSION: DATE : NUMÉRO DE PIÈCE : PAGE SUBARU OF AMERICA REV. – B 2021-09-14 SOA801P052xx...
- Page 11 Gabarits de portes avant du côté du conducteur : Ce bord devrait être parallèle à la ligne de carrosserie Point de frappe initial NUMÉRO DE PIÈCE : PAGE VERSION: DATE : SUBARU OF AMERICA REV. – B SOA801P052xx 2021-09-14...
- Page 12 Gabarits de portes avant du côté du passager : Ce bord devrait être parallèle à la ligne de carrosserie Point de frappe initial NUMÉRO DE PIÈCE : PAGE VERSION: DATE : SUBARU OF AMERICA REV. – B SOA801P052xx 2021-09-14...
-
Page 13: Forester Wilderness Conducteur Arrière
Gabarits de portes arrière du côté du conducteur : Forester Wilderness Conducteur Arrière Modèle de montage du protège-rebords de portière Point de frappe initial PAGE NUMÉRO DE PIÈCE : VERSION: DATE : SUBARU OF AMERICA REV. – B 2021-09-14 SOA801P052xx... - Page 14 Gabarits de portes arrière du côté du passager : Forester Wilderness Passager Arrière Modèle de montage du protège-rebords de portière Point de frappe initial PAGE VERSION: NUMÉRO DE PIÈCE : DATE : SUBARU OF AMERICA REV. – B 2021-09-14 SOA801P052xx...