Publicité
Liens rapides
INSTALLATION
INSTRUCTIONS
KIT CONTENTS
1. Bumper Corner Molding
2. Alcohol Swab
2003-
2007 -
Baja (Rear Bumper Only)
2006-2007 - Impreza all models (Rear Bumper Only)
2012-Current - Impreza all models (Front Bumper Only)
2006-2013, 2014-2018 - Forester all models
2019 - Current - Forester all models (Rear Bumper Only)
1. Be careful not to scratch the vehicle body or bumpers during installation.
2. Do not wash vehicle for 24 hours following installation of the bumper molding.
3. Special attention: Areas of application must be prepared for proper adhesion of the
mounting tape. The mating surface must be clean, dry, and free of oil and wax. Part WILL
NOT adhere properly if surface has not been completely cleaned of any contaminates.
4. If the temperature is below 60°F (15°C), heat the double sided tape and the bumper surface
to a temperature of 80°F (27°C).
5. Not to be used on unpainted bumpers.
6. Review installation instruction thoroughly prior to installation.
7. Not Applicable to vehicles equipped with Blind Spot Detection.
It is recommended that this product be installed by a trained Subaru Technician at your local
Subaru dealer.
1. Special attention: Clean area of application using alcohol swab. It is critical to use
extra care to ensure proper surface preparation.
2. Measure with a measuring tape and mark using a grease pencil.
3. Center bumper molding and mark using a grease pencil.
4. Without removing red tape liner, check positioning on bumper.
5. Remove half-round and top strip red tape liner.
6. Peel back 1"(2.5cm) to 2"(5cm) of bottom red tape liner from each end and fold down as
shown.
7. Position bumper molding between the grease pencil marks.
8. Peel remaining red liner from behind the bumper molding.
9. Starting from center, apply 40-45 psi
of firm hand pressure for 10 seconds
along the tape area of the molding to
ensure proper bonding.
10/24/2018
PART NUMBER:
DESCRIPTION:
Qty. 2
Qty. 1
APPLICATION
(Rear Bumper Only, Turbo)
PRE-INSTALLATION NOTES
INSTALLATION STEPS
BUMPER CORNER MOLDING
MADE IN HUNGARY
TOOLS REQUIRED
Heat Gun
Measuring Tape
2008-2009 - Legacy Sedan (Front Bumper Only)
2013-2014 - Legacy Sedan (Rear Bumper Only)
2015-Current - Legacy (Rear Bumper Only)
2010-2014 - Outback Wagon (Rear Bumper Only)
1
SOA7181002
Grease Pencil
Cloth
START HERE
Revision 9
Publicité
Manuels Connexes pour Subaru SOA7181002
Sommaire des Matières pour Subaru SOA7181002
- Page 1 7. Not Applicable to vehicles equipped with Blind Spot Detection. INSTALLATION STEPS It is recommended that this product be installed by a trained Subaru Technician at your local Subaru dealer. 1. Special attention: Clean area of application using alcohol swab. It is critical to use extra care to ensure proper surface preparation.
- Page 2 “Ne s'applique pas aux véhicules équipés avec détection d'angle mort“ ÉTAPES DE L'INSTALLATION Ce produit devrait être installé par un technicien Subaru formé de votre concessionnaire Subaru local. 1. Remarque importante : Nettoyer la zone d'application à l'aide d'un tampon imbibé d'alcool.
- Page 3 (Rear Bumper Only) (Front Bumper Only) 2003- BAJA 2008-2009 LEGACY SEDAN (pare-chocs arrière uniquement) (pare-chocs avant uniquement) 1.5" (3.8 cm) 1.0" 21.5" (2.5cm) (54.6cm) (Rear Bumper Only) (Rear Bumper Only) 2006-2008 FORESTER 2009-2013 FORESTER (pare-chocs arrière uniquement) (pare-chocs arrière uniquement) Align to edge 10.0"...
- Page 4 (Front Bumper Only) 2015- IMPREZA (pare-chocs avant uniquement) Align to edge Aligner avec le bord 1.0" (2.5cm) (Rear Bumper Only) 2010- 2014 OUTBACK (pare-chocs arrière uniquement) 1.0" (2.5cm) 2.0” (5.0cm) 0.6” (1.5cm) (Rear Bumper Only) 2013-2014 LEGACY SEDAN (pare-chocs arrière uniquement) Center of exhaust pipe Centre de tube d'échappement 1.55”...