Numark NV II Guide D'utilisation Rapide page 7

40. Quant / +BPM: Press this button to enable or disable Quantize. When enabled, setting and
triggering cues and loops will snap to the Beatgrid. Please see the User Guide for more
information.
Press and hold Shift and then press this button to sort the Library by BPM.
41. Beat Jump / +BPM: Press this button to enable or disable Beat Jump mode for the Pads.
When Beat Jump is enabled, the bottom 4 pads in Auto-Loop and Loop Roll modes will
function as Beat Jump controls. Please see the User Guide for more information.
Press and hold Shift and then press this button to sort the Library by BPM.
42. S. View / +Key: Press this button to toggle through the available software display modes.
Press and hold Shift and then press this button to sort the Library by Key.
43. D. View / Column: Press this button to toggle through the available NV
Press and hold Shift and then press this button to display Key, BPM, or Time in the Library.
Pitch Controls
44. Range / Keylock: Press this to adjust the range of the Pitch Fader to ±8%, ±16%, and ±50%.
Press and hold Shift and then press this button to activate or deactivate Keylock: the key of the
song will lock to whatever position the pitch fader is at when Keylock is activated. This feature
allows you to change the speed of the song without changing the key.
45. Takeover LEDs: When you select the other Deck with the Deck Select switch, the position of
the NV 's Pitch Fader may not match the Pitch setting for that Deck in the software. Slowly
II
move the Pitch Fader in the direction indicated by the Takeover LED arrow until it turns off. At
this point, the Pitch Fader matches the Pitch setting in the software and can control it again.
46. Pitch Fader: Controls the track's playback speed. An LED next to the fader will light up when
set at 0%.
47. Pitch Bend ( + / – ): Press or hold down either of these buttons to temporarily adjust the track's
playback speed. When released, the track playback will return to the speed designated by the
Pitch Fader.
48. Beatkeeper: This meter is an aid for matching the tempo of both decks. When the white center
LED is lit, the BPMs are matched. Otherwise, the meter will tend towards the faster deck. The
further from center, the greater the difference between the two BPMs.
Effects Controls
49. FX 1, FX 2, FX 3: These buttons have different functions on each Deck depending on the
current FX Mode: Single-FX Mode or Multi-FX Mode. Please see the User Guide for more
information.
50. FX 1 Knob, FX 2 Knob, FX 3 Knob: These knobs have different functions on each Deck
depending on the current FX Mode: Single-FX Mode or Multi-FX Mode. Please see the User
Guide for more information.
51. Beat / Mode: Tap this button repeatedly at the desired tempo to set the rate of the effects'
low-frequency oscillators (LFOs). Press and hold this button to reset Beat Multiplier to the
Deck's BPM. Press and hold Shift and then press this button to switch between Single-FX
Mode and Multi-FX Mode.
52. Beat Knob: Turn this knob to set the Time Division for the selected effects.
53. FX Assign: Use these buttons to apply Effect A and/or B to the corresponding channel. You
can apply Effect A and/or B to the entire Program Mix by using the FX Send buttons below the
Master Volume knob. (Each effect can be applied to any or all of the four channels and/or the
Program Mix.)
54. Channel Filter: Turn this knob to adjust the filter on the corresponding channel. The type of
filter it adjusts will depend on the Filter Mode button.
55.
Filter Mode: Press this button to toggle through the Filter Modes, which affect the Channel
Filter knobs: Off, Filter-Roll Mode, or Filter-FX Mode. Please see the User Guide for more
information.
display modes.
II
7