Nice volo s-radio Instructions Et Recommandations Pour L'installateur page 4

5) Programming
If the SUN or WIND cut-in levels are not suitable for the application, they can be modified according to your requirements (awning dimensions, posi-
tion, weather requirements). The SUN and WIND cut-in levels can be modified separately using button (
and 6 SUN values, as shown in Tables B1 and B2.
Table "B1" WIND levels
Level N. 1 = 5 Km/h
Level N. 2 = 10 Km/h
Level N. 3 = 15 Km/h
Level N. 4 = 30 Km/h
Level N. 5 = 45 Km/h
To modify the cut-in levels, follow the instructions in Tables C1 and C2.
Table "C1" Modifying the "WIND" protection cut-in level (Fig.8)
1. Press and release the button. When the button is released, the RED LED lights
up and stays on, indicating the WIND programming stage.
2. Wait until you hear a beep.
3. Within 4 seconds press and release the button 1 to 5 times according to the desired
level (see Table B1).
4. After a few seconds you will hear a number of beeps, accompanied by RED flashes,
corresponding to the set WIND level; subsequently, the RED LED will stay on.
5. Within 4 seconds, press the button once
to confirm; you will hear three long beeps and the LED will go off.
Note 1 If, for any reason, you should make a mistake in the programming, a series of short beeps
and flashes will signal the fact.
Note 2 When the programming procedure has been completed, the set levels will be indicated by a
corresponding number of RED flashes (WIND) followed by GREEN flashes (SUN).
Table "C2" Change or delete the level of the "sun" (Fig.9)
1. Press and release the button twice. When the button is released, the GREEN LED lights up
and stays on, indicating the SUN programming stage.
2. Wait until you hear a beep.
3. Within 4 seconds press and release the button 1 to 7 times according to the desired
level (see Table B2).
4. After a few seconds you will hear a number of beeps, accompanied by GREEN flashes,
corresponding to the set SUN level; subsequently, the GREEN LED will stay on.
5. Within 4 seconds, press the button once
to confirm; you will hear three long beeps and the LED will go off.
Note 1 If, for any reason, you should make a mistake in the programming, a series of short beeps
and flashes will signal the fact.
Note 2 When the programming procedure has been completed, the set levels will be indicated by a
corresponding number of RED flashes (WIND) followed by GREEN flashes (SUN).
(7 flashes indicate "Delete")
4
Table "B2" SUN levels
Level N. 1 = 2 KLux
Level N. 2 = 5 KLux
Level N. 3 = 10 KLux
Level N. 4 = 20 KLux
Level N. 5 = 40 KLux
Level N. 6 = Current KLux value
Level N. 7 = Delete
Note: In the programming of SUN level 6, the brightness value
measured at the time of programming is memorized
); you can select from 5 WIND values
Example
X1 = 5 Km/h
X2 = 10 Km/h
X3 = 15 Km/h
X4 = 30 Km/h
X5 = 45 Km/h
X1 = 5 Km/h
X2 = 10 Km/h
X3 = 15 Km/h
X4 = 30 Km/h
X5 = 45 Km/h
!!!
Example
X1 = 2 KLux
X2 = 5 KLux
X3 = 10 KLux
X4 = 20 KLux
X5 = 40 KLux
X6 = Auto
X7 = Delete
X1 = 2 KLux
X2 = 5 KLux
X3 = 10 KLux
X4 = 20 KLux
X5 = 40 KLux
X6 = Auto
X7 = Delete
!!!