Troubleshooting Guide; Technical Specifications - Avent ISIS iQ DUO Mode D'emploi

Troubleshooting Guide

Check that all the pump components have been assembled
°
correctly and that the white valve is positioned correctly.
Ensure that the silicone diaphragm and Let-down Massage Cushion
°
Lack of suction
securely to the pump body and a perfect seal is created, making sure to push
the Let-down Massage Cushion far enough down the center of the funnel.
Make certain that the tubing connections and control handle are firmly in place.
°
Ensure the pump is correctly assembled and that suction is being created.
°
No milk being
Relax and try again, as expression may improve after practice.
°
expressed
Refer to the 'Preparing to Pump' section on page 7.
°
You may be pumping too hard. You do not need to use all the suction
°
the pump can generate. Try compressing the handle halfway.
Pain when
Try holding down the pump handle for 2-3 seconds per compression.
expressing
°
Consult your health professional or breastfeeding advisor.
°
Try leaning slightly forward.
°
Remove and re-fit the Let-down Massage Cushion to ensure it is firmly
Milk is drawn up
°
attached and pushed far enough down the center of the funnel.
the Let-down
Some women may prefer to use the pump without the Let-down Massage Cushion. The Let-
Massage Cushion
down Massage Cushion has petals that flex in and out to gently massage the area around the
breast. This is intended to help stimulate a fast, natural milk flow. When using the breast pump
without the Let-down Massage Cushion, the maximum vacuum level achievable will be higher.
Avoid contact with antibacterial detergents or cleaners as they can damage the
°
plastic. Combinations of detergents, cleaning products, sanitizing solution,
Cracking or
softened water and temperature fluctuations may, under certain circumstances,
discoloration
cause the plastic to crack. If this occurs, do not use. The pump bodies and breast
milk containers are dishwasher safe but food colorings may discolor them.
of pump parts
Follow guidelines in 'Cleaning and sanitizing your ISIS iQ DUO
instruction booklet.
Contact AVENT for replacements.
°
Lost or broken parts
Call 1.800.54.AVENT or visit www.aventamerica.com
Ensure the pump is correctly assembled and switched on with the power
°
Pump not responding
indicator illuminated GREEN.
to pressing of the
Make sure the cables between the electric wall socket and the pump are
°
control handle
correctly connected.
If the pump stops working and the power light is flashing
°
been detected.
3 flashes, delay, 3 flashes, etc – the ISIS iQ has detected a vacuum fault. Switch
°
off the motor and check tubing and connections for obstructions or damage.
Pump light
2 flashes, delay, 2 flashes, etc – the ISIS iQ has detected that it is over the acceptable
°
flashing RED
temperature. Switch off the motor. Ensure unit is not exposed to heat sources or
sitting in direct sunlight. Allow unit to stabilize before trying again.
Continuous flashing – the pump has detected that the control cable has been
°
incorrectly fitted/not fitted or the cable is damaged.
21
™
are fitted
Key to product base label
™
on page 6 of the
RED then a fault has
Need Help? Call us at 1.800.54.AVENT or visit www.aventamerica.com

Technical Specifications

TYPE B APPLIED PART
FOLLOW OPERATING
INSTRUCTIONS
LISTED
3045297
FOR INDOOR USE ONLY
Technical Specifications:
Mains Input Voltage 100 – 240 VAC
°
Mains Input Current 1.5A
°
Mains Input Frequency 50 – 60 Hz
°
Supply voltage fluctuations not exceeding
°
+/- 10% of the nominal voltage
Ambient temperature range: +10° C to
°
+40° C (+50° F to +104° F)
Relative Humidity range: 30% to 75%
°
Atmospheric Pressure: 700 to 1060hPa
°
Equipment rated for continuous operation
°
GENERAL WARNING
ETL LISTED MARK –
CANADA/UNITED STATES
CLASS II EQUIPMENT
22