Krick ro marin Dusseldorf Mode D'emploi page 52

Glue the bearing bushes and frame (superglue) so that the extinguishing head "A" can be turned easily.
Make sure that the frame is about 10 mm from the front and rear edges of the cover (52) (drawing). Sand the
bearing bush laterally flush with the servo plates (113) and (114).
Now fix the Ø 28 mm belt pulley (116) with the M 3 x 6 grub screw (117) on the pipe (Mo4). Fit the tubular
rivet (118) and secure with a drop of "UHU hard". The purpose of the tubular rivet is to protect the nylon cord
at the deflection from chafing.
The control disc (servo disc) supplied with the servos is now screwed twice to the large Ø 68 mm belt pulley
(119) (M 2 x 6 screw (213) and M 2 nut (112)).
Mount the swivel servo (121) in the holder (120) according to the plan and photos and fit the disc (119).
The unit should be positioned (plan + photos) so that the pulleys are at one height and at least 5mm apart.
Now loop the belt pulleys with the cord (123) once or twice according to the extra illustration and knot the
tension spring (124) between them with little tension. Set the servo and erase head to neutral and push the
spring to the position indicated on the plan. The monitor A is now ready for horizontal swivelling.
Mount the lift servo (126) in the holder (125). Fasten the perforated, one-sided lifting lever made of ABS
(127) to the servo disc with a screw (128). The lever (127) is set later. The unit according to the plan and
photos should be aligned so that the lever is at the same height as the edge of the tubular rivet (118). Fix the
holder and fasten it with self-tapping screws (122). Move the lift servo with the RC system to the position in
which the highest pipe elevation of the monitor "A" is to be achieved. Insert the Perlon thread Mo22 into the
inner hole Ø 1 mm (small stroke) of the lifting lever and fix it with the clamping screw (129) with U-disc (130).
Now move the servo in the opposite direction to the stop and check whether the erase head has reached the
lowest point.
Insert the complete monitor "A" assembly in the boat, screw on the cover and check its function with
transmitter and receiver. The final connection is made later, as is the connection to the pump.
Monitors B and C:
After the monitor "A" is ready for use, the two monitors "B" and "C" are now mounted on the cabin 56, which
is ready for use. They are removed again later, before painting the cabin. The ABS disc (131) (Ø 48 mm) is
cut out. Under the prefabricated grating "B" (107) the red lacquered disc is aligned and glued. Center the foot
(Mo2) with the aid of the bearing bush (Mo1), align it as shown on the grating and drill Ø 2 mm through the
washer (131). Align the grating "B" on the roof of the cabin exactly, drill the Ø 2 mm holes. In the middle of
the Ø 15 mm hole (part 131) drill through the roof step by step to Ø 8 - 10 mm. Screw on foot and grating
"B". (screws (111) and nuts (112))) Drill into the centre of the platform for monitor "C" Ø 8 - 10 mm in steps.
The foot "C" is aligned in its position and bolted as for "B".
Then remove the servo plate (132). The recesses for the servos may need to be widened so that the
intended steering gear with the output is at the marked point on the plate. (The distances between the
moving parts and the sides of the cab must be sufficiently large).
Double up the plywood spacer blocks (133) 5x8 mm to obtain a height of 10 mm. Glue these for the lift servo
(134) and prime the whole plate (132). Insert the plate into the cabin, push it backwards and align it with the
monitor shafts "B" and "C" (Mo4) so that they are approximately in the middle of the corresponding recess.
Fix the plate with acrylite. Then place the bearing flanges Mo1 (Ø 2.5 mm boring) on the pipes Mo4 and align
them so that the extinguishing heads "B" and "C" are very easy to turn. Fix with superglue and fasten the
flanges with the screws (135).
To prevent the monitors from moving upwards, they are secured with the 15/7 adjusting ring (136) and the M
3 x 6 grub screw (117). Now the lift servo (134) and the swivel servo (137) can be inserted and screwed in.
(8 pcs. Ø 2.9 x 6.5 self-tapping screws (122)). Mount the pulley Ø 68 mm (119) as for monitor "A" and place
it on the swivel servo. Align the Ø 28 mm belt pulleys and screw them together. (grub screw 117) . Finally,
attach the scale cord with spring (124) according to the construction plan. (See figure on plan 2: One or two
full surrounds on all discs!
16 © Klaus Krick Modelltechnik, Knittlingen, Germany Status 08/2022