Table des Matières
Manuels Connexes pour a2pro Apache Excellium 480 Serie
Sommaire des Matières pour a2pro Apache Excellium 480 Serie
- Page 1 All manuals and user guides at all-guides.com Assembly manual / Notice de Montage Apache / Bell UH-1D Rotor principal Main rotor / : 810 mm Rotor anticouple Tail rotor / : 180 mm Poids prêt à voler Weight / : 1900g full equiped /...
- Page 2 Merci d’avoir choisi un produit A2PRO / Excellium. This model is developped and manufactured by A2PRO. Ce modèle a été développé et produit par A2PRO. Do not rush in building the model take the time to check the assembly steps and Do not rush in building the model, take the time to check the assembly steps and read the manual before starting to build it.
-
Page 3: Outillage & Accessoires
All manuals and user guides at all-guides.com Tools & accessories Outillage & accessoires Ref: 1229 Ref: 9970 Ref: 9925 Ref: 7821 Ref: 1544 These tools and furnitures are necessary to build your model. Do not hesitate to ask your local retailer for them ! Ces outillages et fournitures sont nécessaires pour le montage de votre machine. -
Page 4: Equipement Électronique
All manuals and user guides at all-guides.com Electronic equipment Equipement électronique U-Bec 5A Pro-Tronik Gyro Ref. : 78480 3x Servos 7500 TG-D (cyclic) Contrôleur / ESC : Pro-Tronik Pm80 XH 1x Servo 7502 TG D (Tail / Anticouple) 1x Servo 7502 TG-D (Tail / Anticouple) Motor Pro-Tronik 480 XH (1600 Kv) ik 480 XH (1600 K ) Li P P... -
Page 5: Before Starting / Avant De Commencer
All manuals and user guides at all-guides.com Before starting / Avant de commencer • The general mechanical assembly is pretty simple. But the assembly must be done with care and fine tuned. The way you will build and maintain your helicopter mechanics will determine the way it will fly and it’s reliability. -
Page 6: Préparation De La Mécanique
All manuals and user guides at all-guides.com Mechanics preparation Préparation de la mécanique The mechanics is delivered pre assembled in the scale fuselage. You will need to remove it in order to install your electronics, adjust the linkages and proceed with thread lock and bearing sealant application. - Page 7 All manuals and user guides at all-guides.com Mechanics preparation Préparation de la mécanique In order to remove the main mechanics, you will need then to remove the screws retaining the mechanics in the fuselage. Do not forget to loose the tail boom support screw to be able to push forward the tail boom assembly to free the belt from the font pulley and then pull out the entire assembly.
- Page 8 All manuals and user guides at all-guides.com Main rotor Hub / Hub Rotor principal Disassembly, check and rebuilding the rotor hub The main rotor head is factory assembled without thread lock on the screws and screws are not tightened. You will need to disassemble the rotor head in order to check it and rebuild it as necessary.
- Page 9 All manuals and user guides at all-guides.com Flybar cage / Cadre de Barre de Bell Before assembling and installing the flybar cage do not forget to install the rod ends ! Before assembling and installing the flybar cage, do not forget to install the rod ends ! You will need to apply thread lock on the 4 screws of the flybar cage.
- Page 10 All manuals and user guides at all-guides.com Flybar Pivot / Pivot de Barre de Bell The flybar pivot assembly does not show any difficulty. Just be careful when tightening the screws in order not to damage the plastic threads Aluminium ball shall also be the screws, in order not to damage the plastic threads.
- Page 11 All manuals and user guides at all-guides.com Washout & Swashplate The washout is a very important part. All cyclic and pitch inputs are mixed by that part. This is why that part must be built with care and frequently checked. A small natural slope can be identified and shall remain.
-
Page 12: Washout & Plateau Cyclique
(utiliser un accélérateur est bien pratique dans ces cas là, Ref. A2Pro : 1540). Pensez à dégraisser la pièce avant la manipulation, et en AUCUN CAS il faut que les leviers ne soient collés ensembles, l’articulation doit se faire correctement. - Page 13 All manuals and user guides at all-guides.com Washout FREIN FILET / THREAD LOCK CYANO / CA SCELLE ROULEMENT / BEARING SEALANT 808627 808625 808232 808232 808268 808944 808944 808268 808673 808624 808626 808627...
-
Page 14: Assemblage De La Tête De Rotor
All manuals and user guides at all-guides.com Main rotor assembly Assemblage de la tête de rotor Screw the main rotor hub and the flybar pivot together. Do not overtighten the screws, this will damage the flybar pivot (808631). Just flip the mixing levers (808633) to get acces to the screws heads. -
Page 15: Installation Des Palettes De Bell
All manuals and user guides at all-guides.com Flybar paddles installation Installation des palettes de bell Check one more time that both sides of the flybar have exactly the same length (L1 and Check one more time that both sides of the flybar have exactly the same length (L1 and L2 on the drawing).You will then need to install the flybar paddles. - Page 16 All manuals and user guides at all-guides.com Servos supports / Supports de servos The servo support system is composed of a tube plus 2 aluminium parts with 3 arms. These aluminium parts, wich allow to install all kind of mini servos, are secured and locked with M3x3 screws.
- Page 17 All manuals and user guides at all-guides.com Tail transmission / Transmission AC This part of the mechanics require a specific care.The helicopter flight performances and controls are directly linked to the tail rotor operation smoothness and precision. Lube the one way bearing in the main pulley. Be sure that the tail rotor gearbox and belt are correctly installed.
-
Page 18: Main Mechanics / Mécanique Principale
All manuals and user guides at all-guides.com Main mechanics / Mécanique principale The assembly of the main mechanics has to be performed on a perfectly flat surface to The assembly of the main mechanics has to be performed on a perfectly flat surface, to allow the best possible alignment of the different components and especially the ball bearing blocks. - Page 19 All manuals and user guides at all-guides.com Main mechanics / Mécanique principale FREIN FILET FREIN FILET THREAD LOCK 808901 808952 808901 808916 808940 808901 808900 808952 808952 808901 808901 808953 808901 The M2x8 screw (808901) and the M2 nut (808940) are maintaining the tail boom.
- Page 20 All manuals and user guides at all-guides.com Main mechanics / Mécanique principale 808619 FREIN FILET THREAD LOCK 808620 808970 808618 808644 808916 808643 808698 808606 808617 808616 808645 808601 808604 808611 808600 808645...
- Page 21 All manuals and user guides at all-guides.com Tail gearbox / Anticouple Do not overtighten the screws in order not to «press» the bearings and mast assemblies Do not overtighten the screws, in order not to «press» the bearings and mast assemblies. This could lead to tail malfunction or excessive current draw, early belt wear and difficult tail control (and obviously tail servo prematurate failure).
- Page 22 All manuals and user guides at all-guides.com Elevated tail / Anticouple surélevé The belt system allows a very easy mechanical system to be used It is build with 2 The belt system allows a very easy mechanical system to be used. It is build with 2 frames, linked to the tail boom with a plastic insert.
-
Page 23: Poulie Du Renvoi D'angle
All manuals and user guides at all-guides.com Lower pulley assembly Poulie du renvoi d’angle FREIN FILET THREAD LOCK 808413 808232 808413 808940 CYANO 808905 Goupille / Pin 808020 808020 808659 808659 808460 808905 808232 808415 808940 808451 808451 808673... - Page 24 All manuals and user guides at all-guides.com Lower pulley assembly Poulie du renvoi d’angle Attention ! Pour le Bell 205 UH-1, la courroie est de type B648MXL, référence 808662 Pour L’Apache, la courroie est de type B549MXL, référence 808748 Pensez à bien centrer la poulie 808412 sur le roulement 808232 avant de coller la poulie sur le roulement avec du scelle roulement ! Cela évitera des frottements poulie sur le roulement avec du scelle roulement ! Cela évitera des frottements parasites.
-
Page 25: Tail Hub / Hub D'anticouple
All manuals and user guides at all-guides.com Tail hub / Hub d’anticouple Warning! You will need to put some thread lock in the hub threads to secure the blade Warning! You will need to put some thread lock in the hub threads to secure the blade grips installation. - Page 26 All manuals and user guides at all-guides.com Tail hub / Hub d’anticouple FREIN FILET THREAD LOCK 808900 808232 808261 808663 808232 808900 808943 808902 808666 808293 808664 808293 808902 808666 Le hub est fixé avec une vis M3x3 (808970) A M3x3 screw (808970) secures the hub on the shaft 808484 808661 Axe + poulie + goupille...
- Page 27 All manuals and user guides at all-guides.com Electronics installation The main and tail mechanics are now assembled The main and tail mechanics are now assembled. They will be assembled together after installation of the main mechanics in the body of the scale fuselage.
-
Page 28: Installation De L'électronique
All manuals and user guides at all-guides.com Installation de l’électronique La mécanique principale ainsi que l’anticouple sont maintenant assemblés La mécanique principale ainsi que l anticouple sont maintenant assemblés. La mise en place de l’anticouple sera faite l’installation de la mécanique principale dans le fuselage. -
Page 29: Servos Setting / Installation Des Servos
All manuals and user guides at all-guides.com Servos setting / Installation des servos B = 30mm C = 50mm Fixez votre gyroscope sur le support avec du double face Stick your gyro using double sided tape D=48mm... -
Page 30: Réglages Ac Avant Installation Dans Le Fuselage
All manuals and user guides at all-guides.com Tail setting before fitting in the scale body Réglages AC avant installation dans le fuselage Servo d’anticouple au neutre, le renvoi d’anticouple doit ° être à 45 Ne vous fiez pas à l’angle des flancs de carter AC ! Ajustez la longueur des tringles si nécessaire. - Page 31 All manuals and user guides at all-guides.com Apache landing gear details / Détails des train d’atterrissage de l’Apache 808752 Train principal complet Main landing gear set 808751 Roulette arrière complète Roulette arrière complète Tail wheel complet set...
-
Page 32: Illustrations Pour Le Démontage
All manuals and user guides at all-guides.com Removal drawings Illustrations pour le démontage Removing the Apache tail cover Démontage cache anticouple Apache Don’t forget to remove the tail remove the tail blades ! Ne pas oublier de Vis de maintien Retaining screws retirer les pales d’... - Page 33 All manuals and user guides at all-guides.com Overall view / Vue d’ensemble APACHE Bell 205 UH-1...
-
Page 34: Réglages Radio
All manuals and user guides at all-guides.com Réglages radio Avant de commencer les réglages de votre émetteur, veillez à déconnecter les biellettes de tous les servos ! Les réglages ci-dessous sont possibles sur toute radio programmable. Il vous faut créer un nouveau programme, type «Hélicoptère», avec plateau cyclique °... - Page 35 All manuals and user guides at all-guides.com Réglages radio Ensuite, il faudra régler une courbe de gaz qui vous permette de voler en stationnaire avec au moins 70 / 75% de gaz, afin de ne pas surcharger le moteur avec une vitesse de 70 / 75% d fi d rotation du rotor trop faible et un pas trop important.
-
Page 36: Radio Settings
All manuals and user guides at all-guides.com Radio settings Prior to set your transmitter, please disconnect every pushrod connected to the servos ! The following settings can be used with any heli transmitter. You have to create a new «heli» model memory with 120°CCPM swashplate ON (3 servos directly connected to the swashplate). - Page 37 All manuals and user guides at all-guides.com Radio settings Set you throttle curve to 70/75% on the hover point in order not to over load the motor by th ttl t 70/75% th h i t i d th having too much pitch angle without enough head speed. Basic values are : 0 –...
- Page 38 All manuals and user guides at all-guides.com...
- Page 39 All manuals and user guides at all-guides.com...
- Page 40 All manuals and user guides at all-guides.com...
- Page 41 All manuals and user guides at all-guides.com...
- Page 42 All manuals and user guides at all-guides.com...
- Page 43 All manuals and user guides at all-guides.com...
- Page 44 All manuals and user guides at all-guides.com...
- Page 45 All manuals and user guides at all-guides.com...
- Page 46 All manuals and user guides at all-guides.com...
- Page 47 All manuals and user guides at all-guides.com...
- Page 48 All manuals and user guides at all-guides.com...
- Page 49 All manuals and user guides at all-guides.com...