SSS Siedle HTV 840-0 Montage page 20

Setting the call tone volume
16 The potentiometer for setting
the call tone volume is accessible
under the lettering insert.
17 Assignment of device buttons.
Accessories for HTV 840-...
• ZTV 840-... for conversion from a
wall-mounted to a table-top unit.
Commissioning
Following correct completion of
mounting and installation, the
address is set at each unit while
disconnected from the power
supply (Fig. 13, setting device
address).
A maximum of 4 devices can be
given the same address, meaning
that these devices are then switched
in parallel.
The system is switched on in a
central location and is then ready
for operation after a short delay in
its as-delivered status (basic
configuration 6).
Define the configuration
In the as-delivered status, basic
configuration 6 is always defined. A
configuration cannot be deleted but
only overwritten.
Devices (HTV 840-...) can be given
different configurations within one
system. In this case, the
performance scope of the entire
system is always oriented to the
lowest configuration stage.
However, mixed operation is only
admissible between configurations
1-3 & 4-6.
Programming switch setting
When performing manual
programming at the sliding switch,
set switch 10 (FP) for programming
to "ON" and then for the operating
status back to "OFF".
If an SCO 740-... is integrated in the
system, the switch must always be
set to "OFF".
Basic configuration
The 6 defined basic configurations
can be accessed without any
additional aids. With the sliding
14
switch 10 (FP) switched on press the
light and door release button
simultaneously, hold down and
additionally press the numbers (1-6)
for the required configuration.
After appr. 3 seconds, the two LEDs
under the door release and light
button briefly light up. The
configuration for this device is now
confirmed. An acknowledgement
tone also sounds in the handset.
The sliding switch 10 (FP) must
be switched off again after
configuration.
System configuration
With the aid of the system
configuration, all connected
HTV 840-... units can be configured
with all the system's configuration
possibilities. The basic requirement
for system configuration is always a
system controller SCO 740-...
Through a PRI 602-... it is possible to
connect a PC which simplifies the
configuration process. This allows
the configuration of all users to be
read out, saved and printed.
For more details, see the
programming instructions for the
SCO 740-...
Extended configuration
In the extended configuration,
suitably trained specialists have the
opportunity to carry out individual
changes in the configuration.
However, a thorough understanding
and knowledge of the system are
mandatory for this.
Video memory
The picture save function is
deactivated in the as-delivered
status. If required, it has to be
activated using the SCO
programming software. This
function is only possible provided a
sufficient video power supply is
available!
If a picture is saved, this is indicated
by the LED underneath the DR
button.
The display can be set using the
programming software to any
optional LED. In addition, an
optional button can be assigned the
function "Display saved pictures"
for direct access to the saved picture
library. In the as-delivered status,
saved pictures can be accessed using
the Enter button.
If the system includes cameras with
a swivel and tilt function, the
direction buttons of the video
control system can be used to
actuate the swivel and tilt
movements.
When selected using the "Control"
button, the picture remains full size
on the screen and the camera can
be controlled using the direction
buttons. Using the "Back"
function, the video module is
returned to normal mode.
For more detailed information,
contact the Siedle-Multi hotline
Tel. +49 7723 63-378
Video memory
The device's video memory is only
active if the Multi telephone has an
additional power supply (dimension
the video power supply accordingly
in the whole system). It stores the
last 28 pictures taken by the door
camera. In the event of a power
failure, the video memory is deleted.
The device's video memory is able to
save 28 pictures from the door
camera.
Pictures saved in the device are
erased after a power failure. The
video memory is only functional
when the video supply voltage has
been dimensioned accordingly
throughout the whole system.
Setting the language, date and
time
After first switching on the monitor,
the language must be selected. The
display then changes over to the
input of date and time. If there is a
system clock available in the Multi
system, the time is automatically
updated.