Timer Function; Safety Switch Off Function - Teka TZC 32320 BK TTC Instructions Pour L'installation

After at least 10 seconds have elapsed
since the beginning of the automatic
cook start function:
1 The hot plate must be selected.
2 Press touch key
indicator reaches level 9 and the
automatic cook start function will
be deactivated.

Timer Function

This function makes it easier to cook,
as you do not need to be present
throughout the process: the timed hot
plate(s) will switch off automatically
after the set time has lapsed. There
is a separate timer for each hot plate,
which allows all of the hot plates to be
timed simultaneously.
With these models you can use the
clock as a timer for the hotplates for
times ranging from 1 to 99 minutes. All
the cooking areas can be programmed
individually and in a simultaneous
manner.
TIMING ONE HOTPLATE
1 The cooking zone to be timed must
be selected.
2 Select a power level for the hotplate
from 1 to 9 using the touch keys
or (5/4).
3 Press clock touch key
indicator (12) will display 00. Timed
hot plate display (11) will flash.
4 Immediately afterwards, enter a
cooking time between 1 and 99
minutes, by using the touch keys or
(5/4).
When the power indicator (3) stops
flashing, it will start to count down the
time automatically. The respective
timed hotplate disolay (11) will
continue flashing.
When the clock reaches 01, it will
switch from counting down minutes
to seconds.
Once the selected cooking time has
elapsed, the heating zone being timed
is turned off and the clock emits a
series of beeps for several seconds.
The timer indicator will display a
flashing 00 beside the hotplate that
has been disconnected.
If you wish to time another hotplate at
the same time, repeat steps 3 and 4.
(5) till the
If the heating zone turned off is hot, its
indicator displays an H or otherwise an
0. To turn off the audible signal touch
any sensor.
CHANGING THE PROGRAMMED
TIME
To change the progrmmed time, you
must press the touch key of the timed
hotplate (2) to select it and then the
clock (10). You may then read and
change the time.
DISCONNECTION OF THE TIMER
If you want to stop the timer before the
programmed time is up
1 First select the hotplate and then
press clock touch key
2 Use the touch key
recude the time to 00. The clock is
cancelled.
Alternative metod :
After zone selection if timer touch key
is pressed for two seconds, the related
timer will be cancelled.

Safety switch off function

(10). Timer
If due to an error one or several hot
plates do not switch off, the appliance
will be automatically disconnected
after a set amount of time (see table 2).
Table 2
Selected
power
level
1
2
3
4
5
6
7
8
9
When the "safety switch off" function
has been triggered, a 0 is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
To reconnect the appliance, switch it
off by pressing the on/off key
then switch it on again.
(10).
Keep the control panel of the
heating areas clean and dry at all times.
(4) to
In case of operating problems
or incidents not mentioned in this
manual, disconnect the appliance
and contact the TEKA technical
service.
Recommendation for the
good use of vitroceramic
* Use pots or pans with thick,
completely flat bottoms.
* Pans with a smaller diameter than
the shown heating area are not
recommended.
* Do not slide pots and pans over the
glass as they may scratch it.
* Although the glass can withstand
knocks from large pots and pans
without sharp edges, try not to
knock it.
* To prevent damage to the ceramic
glass induction surface, try not
to slide the pots and pans over
the glass, and keep the bottoms
of the vessels clean and in good
condition.
Try not to spill sugar or
EN
MAXIMUM OPERATION
TIME
(in hours)
10
5
5
4
3
2
2
2
1
(1) and
hobs
37