Samsung Blu-ray BD-E5500 Guide D'utilisation page 19

| NOTE |
\ Depending on your Windows version, the
information may differ.
Wireless Network
You can setup a wireless network connection
in three ways:
- Wireless Automatic
- Wireless Manual
- WPS(PBC)
When you configure the wireless network
connection, any wireless network devices
currently connected through the player
or, if applicable, the player's current wired
connection, will be disconnected.
Wireless (general) - Automatic
Ğ
To setup, follow steps 1 to 3 in "Configuring
Your Network Connection" on page 18.
1. Select Wireless (general) in the
Network Settings screen, and then
press the v button.
The player searches for and then
displays a list of the available networks.
Settings
Network Settings
Display
Select your wireless router from the list:
Audio 1/11
Network
XXXXX WEP
XXXXX WPA
System
XXXXX WPA
Language
XXXXX WPA
Security
XXXXX WEP
Refresh
General
Support
a Previous m Move " Enter ' Return
2.
Select the desired network, and then
press the v button.
The Security screen appears.
3.
On the Security screen, enter your
network's Security Code or Pass
Phrase.
Enter numbers directly using the number
buttons on your remote control. Enter
letters by selecting a letter with an
arrow button, and then pressing the v
button.
4. When done, select done at the bottom
of the screen, and then pressing the
v button. The Network Status screen
appears. The player verifies the network
connection and then connects to the
network.
| NOTE |
\ You should be able to find the Security Code or
Pass Phrase on one of the set up screens you used
to set up your router or modem.
Wireless (general) - Manual
Ğ
If you have a static IP address or the
Automatic procedure does not work, you'll
need to set the Network Settings values
manually.
After following Steps 1 to 3 in "Configuring
Your Network Connection" on page 18.
1. Select Wireless (general) in the
Network Settings screen, and then
press the v button.
The Network Status screen appears.
The player attempts to verify the network
connection and fails.
Settings
Network Settings
Display
MAC Address XX:XX:XX:XX:XX:XX
Audio
IP Address 0.0.0.0
Subnet Mask 0.0.0.0
Network
KT_WLAN Gateway 0.0.0.0
DNS Server 0.0.0.0
System
Language
IP auto setting failed. Try the following to set up IP automatically. Or set up IP
manually by selecting 'IP Settings'.
Security
- Ensure DHCP server is enabled on router and restart router.
- Contact your Internet Service Provider for more information.
General
Support IP Settings Retry OK
a Previous < Move " Enter ' Return
2. Select Ip Settings on the bottom of
the screen, and then pressing the v
button.
The IP Settings screen appears.
3. Select the Ip Mode field, and then set
to Manual.
- For the IP setting values, see "Getting
the IP Settings values" on page 18.
4.
Use the number keypad on your remote
to enter the Network values. Use the
▲▼◄► buttons on the remote to move
from entry field to entry field.
5. When done, highlight OK, and then
press the v button.
The Security screen appears.
6.
On the Security screen, enter your
network's Security Code or Pass
Phrase.
Enter numbers directly using the number
buttons on your remote control. Enter
letters by selecting a letter with an arrow
button, and then press the v button.
7. When done, select done at the bottom
of the screen, and then press the v
button. The Network Status screen
appears. The player verifies the network
connection and then connects to the
network.
WpS(pBC)
Ğ
To setup, follow steps 1 to 3 in "Configuring
Your Network Connection" on page 18.
1. Select WpS(pBC) in the Network
Settings screen, and then press the v
button.
The player searches for and then
displays a list of the available networks.
2. Press the WpS(pBC) button on your
router within two minutes. Your player
automatically acquires all the network
settings values it needs and connects
to your network. The Network Status
screen appears. The player connects
to the network after the network
connection is verified.
English
19 |