Specific Safety Rules - Ryobi BG828 Manuel D'utilisation

 INSPECT TOOL CORDS PERIODICALLY. If
damaged, have repaired by a qualified service technician at
an authorized service facility. The conductor with insulation
having an outer surface that is green with or without yellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating grinding wheels.
 INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
 GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole electri-
cal receptacle.
 CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
 USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool's plug.
 DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
 NEVER reach to pick up a workpiece, a piece of scrap,
or anything else that is in or near the grinding path of the
wheel.
 AVOID AWKWARD OPERATIONS AND HAND POSI-
TIONS where a sudden slip could cause your hand to
move into the wheel. ALWAYS make sure you have good
balance.
 NEVER stand or have any part of your body in line with
the path of the wheel.
 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
 DO NOT TURN THE MOTOR SWITCH ON AND OFF
RAPIDLY. This could cause the wheel to loosen and could
create a hazard. Should this ever occur, stand clear and
allow the wheel to come to a complete stop. Disconnect
your grinder from the power supply and securely retighten
the wheel nut.
All manuals and user guides at all-guides.com
GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

3 – English
 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
 USE ONLY CORRECT WHEELS. Do not use wheels
with incorrect size holes. Never use wheel wash-
ers or wheel bolts that are defective or incorrect. The
maximum wheel capacity of your grinder is 8in.
 NEVER TOUCH WHEEL or other moving parts during
use.
 NEVER START A TOOL WHEN ANY ROTATING
C O M P O N E N T I S I N C O N TA C T W I T H T H E
WORKPIECE.
 DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
 WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
 USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
 DOUBLE CHECK ALL SETUPS. Make sure wheel is
tight and not making contact with workpiece before
connecting to power supply.
 USE ONLY FLANGES furnished with this bench
grinder.
 IF ANY PART OF THIS GRINDER IS MISSING or should
break, bend, or fail in any way, or should any electrical
component fail to perform properly, shut off the power
switch, remove the machine plug from the power source
and have damaged, missing, or failed parts replaced be-
fore resuming operation.
 MAKE SURE THE GRINDER IS SECURELY MOUNTED
as described in the operating instructions before con-
necting the tool to a power supply.
 DO NOT OVERTIGHTEN THE WHEEL NUT. Exces-
sive tightening can cause the wheel to crack during
operation.
 ALWAYS USE THE GRINDER'S WHEEL GUARDS AND
SPARK SHIELDS.
 INSPECT GRINDING WHEEL for visible defects. Check
the wheel for fissures and cracks, and test for normal
operation prior to use. Replace cracked wheel immedi-
ately.