Charging The Rechargeable Battery; Operating Elements And Operation - TOOLCRAFT 82 09 21 Notice D'emploi

b) Operating the cordless drill / screwdriver
• Rotating parts can catch your hair and clothes, there is risk of injury! Therefore, use a hair net or something like that
for long hair and wear clothes which fit closely when operating the product.
• Always check the cordless screwdriver and the rechargeable battery for damage before using them. In case you
notice any damage, do not operate the device and bring it to a specialist workshop.
• For safety reasons, the change-over switch is to set to its central position before inserting or replacing the
rechargeable battery and before inserting or removing the bore bits or drills. In this position the drive is blocked
(turn-on lock).
• Ensure that power, gas or water lines are not damaged during boring or screwing in screws! Mortal danger!
• Take special care if you screw in long screws because they might jam or the cordless screwdriver might slip down,
risk of injury!
• Never subject the cordless screwdriver to such a high load that the drive will stop.
• When boring or screwing above your head, put on appropriate safety goggles. Your eyes might be injured by bore
dust or chips. In some cases an additional breathing mask should be worn which protects your nose, mouth and
lungs from dust, an ear protection is recommended as well.
• In some cases an additional breathing mask should be worn which protects your nose, mouth and lungs from dust,
an ear protection is recommended as well.
• If boring or screwing above your head, do not use the magnetic holder on the top side of the cordless drill /
screwdriver. The screws at this holder could fall down (e.g. into your face/eyes), risk of injury!
• Hold the cordless screwdriver safely. In case of a sudden stop of the drive (for example, if a drill is interlocked) the
torque is transmitted to the cordless screwdriver itself, it distorts laterally. Due to this, the cordless screwdriver
might fall out of your hand, risk of injury!
c) Rechargeable battery and charging set
• The rechargeable battery may only be charged via the supplied charging set. Only use the charging set for the
supplied rechargeable battery.
• Only charge the rechargeable battery at an ambient temperature of about 10°C to 30°C.
• If the rechargeable battery has warmed up (e.g. in longer periods of operating the cordless screwdriver) allow it to
cool down before charging it.
• Only recharge the rechargeable battery if it is completely discharged. If an rechargeable battery not being totally
discharged is recharged several times subsequently or if it is recharged after a short period of operation, the
operating life of the rechargeable battery will be reduced and capacity losses will be caused (memory effect).
• The NiCd rechargeable battery used will discharge itself slowly, if it is not used (so called self-discharge). If you do
not use the cordless screwdriver for a longer period of time, check the charge state (state indicator on the top of
the cordless screwdriver) and recharge the rechargeable battery at regular intervals, approximately every 3 months.
• Protect both the rechargeable battery and the cordless screwdriver or the charging set against strong coldness, heat
or direct sunlight. Contrary ambient conditions can not only reduce the operating life of the rechargeable battery but
also cause risk of explosion or of destruction of the rechargeable battery in extreme cases.
• Do not throw the rechargeable battery into fire, risk of explosion!
• Handle the rechargeable battery carefully, ensure that it (and the cordless screwdriver) does not fall down. Due to
the heavy weight, there is not only the risk of destroying the rechargeable battery and the cordless screwdriver but
also risk of injury.
• Never take the rechargeable battery apart.
• Short circuits of the contacts of the rechargeable battery can cause risks of fi re and explosion! Therefore, always
leave the rechargeable battery in the cordless screwdriver.
• Protect the contacts of the rechargeable battery by means of an insulating tape, if the rechargeable battery is kept
separately from the cordless screwdriver.
20
All manuals and user guides at all-guides.com

5. Charging the rechargeable battery

a) General
Observe all safety instructions contained in these operating instructions without fail, chapter 4. c) in particular.
Before operating the product for the first time, the rechargeable battery is to be charged.
A new rechargeable battery or a rechargeable battery which has not been used for a longer period of time reaches its full power
only after 5 complete discharge and recharge processes.
The rechargeable battery needs to be charged if the cordless screwdriver:
• moves very slowly without any load.
• is stored for longer periods of time (every 3 months).
Follow this procedure to recharge the rechargeable battery:
• Connect the charging set to the mains voltage (100 – 240 V/AC, 50/60 Hz). The POWER LED lights up in yellow.
• Take the rechargeable battery out of the cordless screwdriver. To do this, press the two lateral push buttons for unlocking the rechargeable
battery and pull out the rechargeable battery. See also chapter 6 for this step.
• Plug in the rechargeable battery with the correct orientation (only one is possible) into the socket of the charging set (do not apply any force!).
The charging LED lights up in red.
• If the rechargeable battery is completely charged, the charging LED lights up in green(rechargeable battery is fully charged).
A complete charging process takes approximately between 1 and 2 hours.
• Remove the rechargeable battery out of the charging set directly after the end of the charging process.
• Disconnect the charging set from the mains voltage. Pull the mains plug out of the mains socket.
• Insert the rechargeable battery into the cordless screwdriver so that it engages.
Only one direction of the rechargeable battery is correct, do not apply any force when inserting the rechargeable
battery into the cordless screwdriver.
b) Charging LED status indication
Symptom Possible cause
Battery overheated
Battery pack is not plugged in properly.
Flashing in green
Flashing in green and red Abnormal / defective battery pack.

6. Operating elements and Operation

a) General
Please refer to page 3
9. Quick-action chuck
10. Torque-setting ring
11. Display for rechargeable battery state (with test key)
12. Switch for two-speed gear ("LOW" = slow, "HIGH" = fast)
13. Change-over switch with turn-on lock
14. Rechargeable battery
15. Push-button for unlocking the rechargeable battery
16. On/off switch
Solution
Let the battery cool down before charging.
Plug in the rechargeable battery properly, check the battery
contact and make sure the charging LED is showing the correct
charging status (red).
Replace it with a battery of the same type.
21