LUXSAR VD320A-IR Guide De Démarrage

1. GENERAL
The DSP color dome camera VD320A-IR incorporates advanced 1/3" high performing
CCD Sensor and digital signal processor (DSP) circuit.
High quality picture, aesthetic and easy to install, the VD320A-IR are good complement
for your line of CCTV system.
2. FEATURES
2.1. Automatic tracing white balance
The color CCD camera VD320A-IR employ Auto Tracing White Balance adjust-
ment circuit that adjusts continuously the picture as lighting conditions change
for making the correct White Balance adjustment Auto.
2.2. Automatic gain Control (AGC)
The adoption of an Automatic Gain Control (AGC) provides clear image in low
light condition.
2.3. Auto Electronic Shutter (AES)
The color CCD dome camera VD460AF-IR & VD461AF-IR incorporates the Elec-
tronic Shutter up to 1/100,000.
2.4. Back Light Compensation (BLC) - On/Off
As you take a picture with strong light behind the subject, the picture would be
looked very dim on the subject.
In this case, you should select BLC ON, the AES should be in ON position.
NOTE: When you select BLC ON, the AES should be in ON position.
4.2. Step 2
Adjust the camera angel use A & B to get the ideal angel. Adjust the camera
shade angel to match the location of the camera lens.
4.3. Step 3
Place upper cover kit on the top of dome base and screw it by using hex
key wrench.
4.4. Step 4
Complete installation
VD320A-IR
Color dome camera
Vandal proof
2 YEARS WARRANTY
(See conditions of sales abstract)
1
3
3. PRECAUTIONS
3.1. Do not disassemble it or place it on an unstable base.
3.2. Do not touch the surface of CCD sensor by hand directly.
3.3. Never face the camera toward the sun.
3.4. Use proper AC power source otherwise the camera will not function correct-
ly.
3.5. In case the camera with any defect, please inform the qualified service per-
son. Don't try to disassemble the camera by yourself.
4. INSTALLATION PROCEDURE
Camera will be installed as below when Ex-factory
4.1 Step 1
Take out M4 x 16 inner hex socket head screw from upper cover kit by using
3.9 mm hex key wrench then take out the upper cover kit.
5 OVERVIEW
1. Dome Casing
2. 3.9 mm hex key wrench
3. M4 x 16 inner hex socket
head screw
4. Upper cover kit
5. Rubber washer
6. Dome shell
7. PC Ring
8. Cover safety linkage
9. Camera shade
10. Gasket
11. M4 x 4 flat head phillips
12. Dome base
13. Camera shade
14. Camera assembly
7. SPECIFICATIONS
VD320A-IR
PICK UP DEVICE
PICTURE ELEMENTS
SYNC SYSTEM
HORIZONTAL RESOLUTION
MINIMUM ILLUMINATION
BACK LIGHT COMPENSATION
WHITE BALANCE
ELECTRONIC SHUTTER
GAIN CONTROL
GAMMA CORRECTION
S/N RATIO
LENS
DAY/NIGHT COMMUTATION
VIDEO OUTPUT
POWER SOURCE
POWER CONSUMPTION
STORAGE TEMPERATURE
WORKING TEMPERATURE
WATERPROOFING CRITERION IP66
DIMENSIONS
WEIGHT
Designs and specifications are subject to change without notice
2
1/3" Sony CCD
PAL: 500 (h) x 582 (v)
Internal sync
380 TV lines
0.5 lux @ F2.0
On/Off switch
Auto. White Balance (AWB)
Auto. 1/50 to 1/100 000
Automatic
> 0.45
Over 48dB
4.3 mm @ F2.0 varifocal - DC iris
70° horizontal
Digital switch
1.0 Vp-p, 75 ohm
DC 12 V +/- 10 %
185 mA +/- 10 % under 12 V
-30° ~ + 60° C
-10° ~ + 60° C
137 (w) x 137 (l) x 97 (h) mm
Approx. 700 g
VD320A-IR_Manuel_V04
4