Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51235F
Wrenches: 3/4, 21mm & 22mm
Drill Bits: None
Existing weldnut
Note: Fasteners typical both sides
1 1 1 1
Qty. (2)
Hex bolt M14 X 2.0 X 40mm CL 10.9
2 2 2 2
Qty. (2)
Lock washer 9/16"
3 3 3 3
Qty. (2)
Flat washer 9/16"
4 4 4 4
Qty. (6)
Carriage bolt ½-13 X 1-3/4" GR5
Fasteners Typical Both Sides of Vehicle
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
Note: Loosen the spare tire for ease of installment
1. Remove existing M14 bolts from end of each frame rail.
2. Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.
3. Install new M14 bolts through receiver into weldnuts in vehicle frame and into step bumper.
4. Install remaining fasteners as shown.
5. Tighten all fasteners to the required torque specification.
6. Re-tighten the spare tire
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc
Printed in Mexico
Installation Instructions
Chevrolet Silverado Pickup 1500
GMC Sierra Pickup 1500
(Requires OEM Bumper)
Note : Factory installed
steel step bumper and
brackets must be used in
conjunction with this
hitch
Frame rail
3
2
1
Tighten all ½-13 GR5 fasteners with torque wrench to75 Lb.-Ft. (102 N*M)
Tighten all M14 CL10.9 fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
4
5
6
7
5 5 5 5
Qty. (6)
Spacer
6 6 6 6
Qty. (6)
Conical washer ½"
7 7 7 7
Qty. (6)
Hex nut ½-13
Sheet 1 of 3
51235N
Part Numbers:
51235
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
8000 (3632 Kg)
800 (363 Kg)
5000 (2270 Kg)
500 (227 Kg)
Accessory Rating
Cross member and step
bumper shown in cut
view for clarity
Note : Factory installed
steel step bumper and
brackets must be used in
conjunction with this
hitch
9-20-13
Rev. B
Form: F205 Rev C 9-17-2012
C
Publicité
Manuels Connexes pour Cequent Performance Products 51235
Sommaire des Matières pour Cequent Performance Products 51235
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc Sheet 1 of 3 51235N 9-20-13 Rev.
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2013 Cequent Performance Products, Inc Feuille 2 de 3...
- Page 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc. Hoja 3 de 3 51235N 9-20-13 Rev.