Your Product; For Your Safety; Electrical Connections - Radialight Plano Mode D'emploi

ENGLISH
OPERATING INSTRUCTIONS
Before operating the heater, please read these instructions thoroughly to avoid damage and
hazardous situations. Any use of this heater other than that stipulated in this instruction manual
may cause fire, electric shock or injury, and voids all warranties.
Warranty does not apply to any defect, deterioration, loss, injury or damage caused by, or as a result
of, the misuse or abuse of this heater. The rights dictated by State law are not prejudiced. None of the
terms of this warranty are to be taken as excluding any conditions or warranties implied by State law,
which cannot be excluded or modified.
Before any operation remove the packaging and check product integrity. In case of defects or damages
do not try to repair it yourself but contact your dealer.
Do not let children play with the packaging and protect the environment by disposing of the packaging
in accordance with the national regulations for waste processing.

1. Your product

Other than the heater you have chosen the package includes (picture 1):
N° 2 metal brackets for wall mounting;
-
N° 1 plastic brackets for wall mounting;
-
- N° 3 nylon plug expansion 8x50mm;
- N° 3 5x60mm cross head screws to fix wall brackets;
Refer to your dealer is something is broken or missing.

2. For your safety

Make sure that the mains power supply matches the rated input: 230V AC, 50Hz.
Never allow animals or children to play with or touch the product. Attention! The panel may
become very hot while it is working (approximately 80° C = 176° F);
WARNING: In order to avoid overheating, do not cover the heater. Do not hang anything on
the heater and do not cover it while it's working. This is clearly written on the cover of the product
or shown by the symbol
This product may not be used by people (children included) with reduced physical, sensorial or
mental capacities, or with inadequate experience and knowledge, unless they are under the
supervision of a person responsible for their safety or have been suitably instructed by the latter.
Children must be supervised to ensure they do not play with the product.
To prevent overheating, never cover the product inappropriately (pictures 9 and 10).
Do not use the product in rooms saturated with explosive gas, vapours generated by solvents or
paints or flammable vapours/gas.
If the cable and/or plug are damaged, do not repair them yourself but take the product to the
technical service or a qualified repair centre and have them repaired by specialised personnel in
order to avoid any risk of damage.
Always position the product so that the plug is immediately accessible.
Never position this appliance immediately underneath a power socket.
3. Safe positioning
Only use the product in its horizontal position;
This product is fitted with a double electrical insulation circuit (class II) and therefore does not
require an earth connection;
Always make observe the minimum distances from walls, furniture and/or objects, as indicated in
picture 2.
Never install the product on a surface made from wood or synthetic material.
This product is water resistant to IP24. It may therefore be used in bathrooms or other areas
subject to humidity provided it is never installed within the perimeter of bathtubs or showers
(Volume 1 of figure 2).
It must never be possible for people in the bath tub or shower to reach the adjustment knobs.
4. Installation
After carefully reading section 3, proceed with installation following the sequence shown in
figures 4 to 8.
Distances indicated in picture 4 are:
Model X (mm)
PLANO45 Min 270 - Max 340
PLANO65 Min 400 - Max 500
PLANO95 Min 600 - Max 800
- Placing metal wall brackets keep in mind that the right bracket must be located in the
lodging realised in the control box of the product. Warning: if you do not respect this
instruction the product may be instable!
- If installation becomes complicated due to the imperfect alignment of the holes, adjust the
position of the wall brackets by loosening the screw a little and moving the connector vertically.
- Fixing the lower bracket(s) in a different position compared to above reported distances is not
recommended! Placing bracket(s) in a different position may endanger product resistance to
knocks. Always mind to insert the lower bracket(s) between two following openings and newer
totally inside only one to prevent side movements (picture 6).

5. Electrical connections

The product must be powered at a voltage of 230V AC 50Hz.
The product must be supplied with a cable and plug or with a cable for installation. If a product
with plug is installed in France, connect it to the mains power supply by cutting off the plug and
using a suitable connection box.
If the product is supplied with a cable for installation, connect it to the mains power supply using a
3-wire cable (Brown=Live, Blue=Neutral, Black=Pilot wire) and a connection box. If you do not
wish to use the pilot wire functions, just connect the phase and the neutral wires: the
product will work correctly even without the external programmer.
In bathrooms, kitchens or other humid areas, install the connection terminal at least 25cm off the
floor.
The electrical connection to the mains power supply must also include a 2-pole switch with a
minimum contact aperture of 3mm. As a priority, always abide you national wiring rules.
It is forbidden to connect the appliance to the earth circuit. DO NOT CONNECT THE PILOT
WIRE (BLACK) TO THE EARTH CIRCUIT.
If the product is powered through a 30mA differential switch, make sure the pilot wire is also
controlled by the differential switch.
L Phase (brown)
Pilot wire (black) – DO NOT CONNECT TO EARTH
N
Neutral (blue)
Y (mm) Z (mm)
535 165
535 265
535 463