Chap. 5. Damges Research And Cleaning - Fama 410.009 Mode D'emploi

CHAP. 5. DAMGES RESEARCH AND CLEANING

BREAKS OR DAMAGES RESEARCH AND MOVING ELEMENTS UNBLOCKING
Here follow are indicate the interventions for the breaks or damages research and moving elements unblocking which can
be performed from maintenance men.
TYPE POTENTIAL CAUSE/S
General Black out
Net voltage
Fuses or magneto thermals intervention
lacking
place upstream of the machine feeding
line
Protection device intervention inside
the machine
Functioning
intervention
Grater group handle lifting
Cause/s not identifiable
Feeding voltage lacking.
Sectioning devices set on "OFF".
The machine
Intervened fuses or not functioning
doesn't
magneto thermals.
function: the
Archimedean
Lacked running button functioning
screw or the
grater roll
don't rotate
Thermal intervention due to the
overheating
Damaged micro switch
CLEANING
It is forbidden to clean by hand the organs and the elements in motion.
All cleaning interventions must be started only and exclusively, after having unloaded the machine with the food product
in working and having insulated from the electric feeding source and from external energy.
The machine, the electric equipment and the machine board components must not be ever washed utilizing water, and not in
any kind of jets form and quantity; so, without "bucket" nor "rubber" nor "towel". Don't put ever directly the machine
in the sink or under the tap.
The machine hygiene level classification and the associated equipment, for the foreseen use, is 2 (two): machine that, after
an hygiene risk evaluation, is in conformance with applicable international standards requirements, but requests a programmed
disassembly for the cleaning.
FREQUENCY PERSONNEL
At the end of every Operator
shift work and
however before the
daily use
410009 en fr de ma 2017
Contact the electric energy distributor
After having eliminated the causes that have determined the protection device
intervention, restore it. In case of problem persistency contact an electrician
technician.
Contact an electrician technician: after having eliminated the causes that have
determined the protection device intervention, restore it.
In case of fuses intervention, change them with types of the same model,
calibration and intervention curve.
Lifting the grater group pressure handle, the machine stops immediately for the
entry in function of the safety micro switch.
Lower the pressure up to the height that doesn't allow the fingers introduction
towards the grater roll and start the machine.
Contact directly the Authorized Assistance Center
Check and restore the electric energy.
Turn the sectioning devices in the position "ON"
Change the intervened fuses, check the magneto thermal switches state.
Check the START button efficiency and eventually contact directly the Authorized
Assistance Center.
Wait the complete cooling before the machine restarting
contact directly the Authorized Assistance Center
All the surface and the machine parts destined to come in contact with the food product or with the
food zones (hopper internal surface, machine neck and the grinding group, the pestle, the pressure,
the grater mouth and the grater roll) and the jets zones (machine external surface) must be cleaned
and disinfected with the under reported modalities. For the grinding group disassembly activities
see the previous descriptions.
 Scrape the surfaces from the possible food product residuals (for example with plastic
scrapers);
 Clean all the food zone surfaces and jets zone with a morbid dampened clothes (not
draining) with detergent diluted in hot water (also common soap for dishes is good). Don't
soak them. With a towel clean inside the grinding mouth. Use specific products for steel or for
the aluminum: which must be liquids (not in cream or pastries however abrasive) and above all
must not contain chlorine. Against the fat substances the denatured alcohol.
 Rinse with cleaned hot water and successively dry all food zone surfaces and jets zone with
soft clothes that don't lose coats.
 Only the STAINLESS steel parts of the mincer group can be washed also in dishwasher, while
the aluminum ones or in cast iron showed in the following table, cannot be washed in
dishwasher.
 The grinding group reassembly must happen only after a working requirement, leave the
pieces wrapped in a dry soft clothes that don't lose coats
MODALITY AND COMPARISONS
MODALITY
11