Setting-Up/Operation - Stadler Form Robert Mode D'emploi

• Do not use damaged extension cords.
• Do not run the power cord over sharp edges and make sure that it does
not get trapped.
• Do not pull the plug from the socket with wet hands or by holding on to
the power cord.
• Do not use the appliance in immediate vicinity of a bath tub, a shower or a
swimming pool (observe a minimum distance of 3 m). Place the appliance
such that a person in the bath tub cannot touch the appliance.
• Do not place the appliance near a heat source. Do not subject the power
cord to direct heat (such as a heated hotplate, open flames, hot iron sole
plates or heaters for example). Protect power cords from oil.
• See to it that the appliance is properly positioned to ensure a high stabil-
ity during its operation and make sure that no one can trip over the power
cord.
• The appliance is not splash-proof.
• For indoor use only.
• Do not store the appliance outdoors.
• Store the appliance in a dry place inaccessible to children (pack the ap-
pliance).
• If the power cord is damaged, it must be replaced by the manufacturer
or a repair shop authorized by the manufacturer or by similarly qualified
persons in order to prevent damage.
• Prior to any maintenance, cleaning and after each use, switch off the ap-
pliance and unplug the mains cable from the socket.
• Do not overfill the water tank beyond the maximum water level mark
'max'.

Setting-Up/Operation

1. Place Robert at the desired position on a flat surface. Connect the
mains cable (3) to a suitable plug socket.
2. Remove the water tank (5) by holding it by the handle and gently pull-
ing it back. Screw off the water tank lid (6) and fill the water tank with
clean, cold tap water. Then screw the lid back onto the water tank.
Place the water tank on the water tray (2). The water tray now fills
slowly with the water from the water tank. Important: please do not
transport Robert as long as he is filled with water. The water could
spill over.
3. To switch Robert on, press the On/Off switch (4). The current relative
humidity is shown in the display in % («Air Humidity»). The «No Water»
indicator (14) lights up when there is not enough water in the appliance.
The speed level is set to the lowest speed and the desired air humidity
is set to continuous operation.
4. If the motion sensor does not detect any motion for 10 seconds, the
illumination of the buttons and the symbols goes out (only the current
relative humidity «Air Humidity» will be displayed in %). Activate the
buttons by moving your hand over the display (9). Alternatively, the dis-
play can also be activated by touching the lower part with your hand.
5. If no mode has been set, the desired air humidity can be adjusted (be-
tween 35-65% and continuous operation «CO»): Push the «Air Humid-
ity» button. The display will blink. You may now select the desired air
humidity in increments of 5% by repeatedly pressing the «Air Humidi-
All manuals and user guides at all-guides.com
ty» button (the display will blink while settings are being adjusted). The
selected value is saved if no other adjustments are made after approx.
10 seconds. The display changes to the current measured air humidity.
Info: Once the desired air humidity is reached, the appliance stops and
the display blinks. The current air humidity is then measured approx.
every 30 minutes (the fan runs for 1-2 minutes). Should the measured
current air humidity fall below the set value, the appliance begins to
humidify again.
6. The humidification performance depends on the speed of the fan. If
no specific mode has been set, the speed level may be changed: Press
the «Speed» button (if necessary, first activate the display with a hand
motion). The display will blink. Now select the speed level 1, 2, 3 or
4 (Turbo) by repeatedly pressing the «Speed» button. The levels are
displayed using horizontal bars (e.g. 1 bar = level 1).
7. Robert is equipped with 3 different pre-programmed modes: «Auto
Mode», «Night Mode» and «Clean Mode». Press the «Mode» button (if
necessary, first activate the display with a hand motion). The display
will blink. Select the mode by repeatedly pressing the «Mode» button:
– «Auto Mode»: Robert automatically maintains the air humidity level
at 45%. The lower the current air humidity level is, the higher the speed
level of the fan will automatically be set (e.g. under 30% = level 3, from
31% to 40% = level 2, from 41% to 45% = level 1).
– «Night Mode»: The display illumination is reduced to minimum and
the fan speed is set on level 1. The desired air humidity level and the
fan speed can be adjusted manually.
– «Clean Mode»: This mode is used in order to clean and descale the
appliance. Here the evaporator discs rotate but the fan does not run.
Thus no air is blown into the room. After 20 minutes in cleaning mode,
the appliance stops and the «Clean Mode» display blinks (see «Clean-
ing» chapter).
8. You can use Robert to disperse fragrances in the room. It must be em-
phasised to please use fragrances extremely sparingly because an ex-
cessive dosage can result in malfunctioning of and damages to the ap-
pliance. In order to use fragrances, remove the water tank (5) and pull
the fragrance container (15) out of the appliance. Let the fragrance drip
directly onto the cotton pad in the fragrance container. Add a maximum
of 1-2 drops of fragrance into the fragrance container.
Tip: In order to change the fragrance, pull the fragrance container out
of the appliance, remove the cotton pad and clean the container with
soap. Now you may insert a new cotton pad (commercially available)
and add drops of the desired fragrance.
9. As soon as the «No Water» symbol (14) lights up, the appliance must be
refilled with water. To do this, remove the water tank (5) and fill it with
clean, cold tap water. After replacing the water tank, the appliance
automatically resumes operation after a few seconds.
10. If you would like to refill the water during operation, you may remove
the water tank and refill it. The appliance will continue to operate us-
ing the water still in the appliance for at least 30 minutes. As long as
the water tank is replaced within this period of time, the appliance can
continue its service without interruption.