Cleaning & Maintenance; Storing The Appliance - Bosch Sensixx B22L Notice D'utilisation

Automatic clean warning
Pilot light (11) will flash indicating that boiler must be
rinsed.
1. Check carefully that the appliance is cold and
unplugged for more than 2 hours, and that the water
tank (1) is empty.
2. Fix the iron to the stand by inserting the tip of the iron
into the front slot and moving the fixation lever (13)
against the heel of the iron.
3. Place your appliance over a sink or bucket.
4. Lean the appliance on the opposite side of the filter
opening.
5. Unscrew the filter (4*) and take it out.
6. (model dependent)
To wash the filter, you may:
a. Place the filter under the water tap and wash it up
until calc residues are removed. Squeeze the filter
as indicated in the picture E.
b. Immerse the filter in tap water (250 ml) mixed with
a measure (25 ml) of descaling fluid.
The descaling fluid can be obtained from our Afters
sales service or from our website.
Accessory code
(Afterssales)
311144
7. Holding your steam generator in the lateral position
and using a jug, fill the boiler with 1/4 litre of water and
replace the filter.
8. Shake the base unit for a few moments, unscrew the
filter again and empty the boiler completely over a sink
or bucket.
For best results, we recommend that this operation is
performed twice.
Important: before resclosing, make sure no water
remains in the boiler.
9. Replace and tighten up the filter.
To reset the "Calc'n'Clean" counter, switch the steam
station off twice, keeping it off for at least 30 seconds
each time.
(on → 30s off → on → 30s off → on)
Rinsing the iron steam chamber (F)
Caution! Risk of burns!
This procedure helps to remove scale particles out of the
steam chamber.
Carry it out approximately every 2 weeks, if the water in
your area is very hard.
a) Ensure that the iron is cooled down.
b) Set the temperature selector (15) of the iron to the
"min" position.
c) Fill the tank with tap water.
d) Plug in the mains cable and set the main power button
(12) to the "I" position (illuminated in red).
e) Wait until the "steam ready" indicator lamp (9) lights
up.
All manuals and user guides at all-guides.com
f) If the steam station has steam regulator (10*), set it to
g) Hold the iron over the sink or a container to collect the
h) Press the steam release button (16) and gently shake
i) Set the temperature selector (15) of the iron to the
j) To clean the soleplate, immediately rub off any residue
Cleaning & Maintenance
Always unplug the appliance from the mains supply
before carrying out any cleaning or maintenance
operation on it.
1. After ironing, pull out the plug and allow the appliance
2. Wipe the housing, handle and iron body with a damp
Name of accessory
(Online shop)
3. If the soleplate is soiled with dirt or scale, clean it with
TDZ1101
4. If the cloth is synthetic, it may melt due to the high
5. Never use abrasive products or solvents. To keep the
Storing the appliance
1. Always allow the appliance to cool down before storing
2. Set the main power button to the "0" position (the red
3. Place the iron on the iron pad (2), standing on the
4. Store the mains cable in the storage compartment (5)
5. Use the iron´s handle when moving the appliance, as
the maximum position .
water.
the iron. Boiling water and steam will come out,
carrying scale and or deposits that might be there.
This could take approximately 5 minutes.
"max" position, without pressing the steam release
button (16). The water in the steam chamber will start
evaporating. Wait until all the water inside the chamber
has been evaporated.
by running the hot iron over dry cotton cloth.
Attention! Risk of burns!
to cool down before cleaning.
cotton cloth.
a damp cotton cloth.
temperature on the soleplate (19). Switch off the
steam and rub off any residue immediately with a
thickly folded, dry cotton cloth.
soleplate (19) smooth, you should avoid hard contact
with metal objects. Never use a scouring pad, or
chemicals to clean the soleplate.
it.
light will go off) and disconnect the mains cable.
soleplate, and fix it by inserting the tip of the iron into
the front slot and moving the lock lever (13) against
the heel of the iron.
and the steam hose in the storage fixing (3). Do not
wrap the cords too tight.
shown in figure G.
en
(G)
13