Focus Mode - Samsung SCC-C6405 Manuel D'instructions

You can select one of four modes for white balance adjustment as follows:
- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the
color temperature is monitored continuously and thereby white balance is
set automatically. The following are the approximate supported color
temperature ranges in these modes.
✻
ATW1 : 2500K ~ 9300K( 1)
ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(
✻ 1. If the color temperature is out of this range in ATW1 mode, proper
white balance may not be obtained. In that case, select ATW2 mode.
✻
2. In ATW2 mode, if one color is dominated in the shooted area, the
color can be displayed differently.
Therefore, select the mode which is appropriate for the environment.
- AWC(Auto-Tracing White Balance Control): In this mode, accurate white
balance is obtained by pressing [ENTER] while having a white paper in
front of the camera. White Balance data will be maintained after set it
once. AWC mode is best in locations where the color temperature of light
source is constant.
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the
white Balance considering the current illumination. Select MANU item
and press [ENTER], the sub screen where you can select Manual White
Balance will be shown. Use the left/right keys to select 3200K, 5600K or
OFF(USER) mode in the PRESET menu.
- 3200K : Set color temperature to 3200K
- 5600K : Set color temperature to 5600K
- USER : Choose out a proper value from the RED and BLUE graph for
color and temperature setup.
(VIDEO SET)
IRIS ALC...
SHUTTER OFF
AGC ON
WHITE BAL MANU...
DIS ON

FOCUS MODE

AF
SPECIAL ...
EXIT QUIT
DIS
The DIS(Digital Image Stabilization) function compensates the camera
screen shaking incurred from vibration.
It is recommended to deactivate the DIS function in the no vibration
environment.
3-13
All manuals and user guides at all-guides.com
✻
(AWB/MANUAL)
➜
Press
[Enter]
PRESET 3200K
RET
FOCUS MODE
In the FOCUS MODE MENU, the Focus method can be set to AF, MF, or ONEAF.
- AF : With AUTO FOCUS MODE, you can monitor the screen continuously
and it will focus automatically. While moving the zoom keys, it will
automatically focus so FOCUS key input is not necessary.
- MF : In MANUAL FOCUS MODE the user adjusts the Focus manually.
- ONEAF : The ONEAF Mode performs Auto-focusing only when the SCC-C6405(P)
2)
stops after moving and when the SCC-C6405(P) is not moving it is same
as MF mode.
(The ONEAF Mode does not work when zooming out.
❈ When in the MF/ONEAF Mode, press the NEAR and FAR keys on the
Use the left/right keys to select AF, MF or ONEAF in the FOCUS MODE menu.
SPECIAL
You may control REVERSE or DETAIL by yourself in the SPECIAL menu.
- REVERSE : Mirrors the screen horizontally, vertically, or in all directions.
- DETAIL
(VIDEO SET)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
EXIT
It's the same as the EXIT function of the CAMERA SET menu.
Controller (SSC-1000/SSC-2000) at the same time to perform AUTO
FOCUS.)
(VIDEO SET)
IRIS ALC...
SHUTTER OFF
AGC OFF
WHITE BAL ATW1
DIS OFF
FOCUS MODE AF
SPECIAL ...
EXIT QUIT
: Controls both horizontal and vertical distinction.
(SPECIAL)
➜
ALC...
OFF
Press
LOW
ATW1
[Enter]
ON
REVERSE
AF
DETAIL
...
RET
QUIT
E
OFF
(0) -- I --
3-14