Kärcher BLV 36-240 Battery Manuel D'instructions Original page 17

3. Allow the lower blower pipe to click into place in the
upper blower pipe.
Illustration D
4. Click the blower pipe in place in the motor casing.
The blower pipe unlocking button must audibly click
into place.
Illustration E
WARNING
Movement of the fan wheels and mulching blades
Incision injuries
Wear protective gloves.
Keep your fingers away from the fan and mulching
blades.
5. If it is not necessary to mount the suction pipe, the
protective grid must be installed. Install the protec-
tive grid if necessary.
Illustration F
a Place the protective grid on the opening of the
motor casing.
b Tighten the protective grid fixing screw until it
clicks audibly.
The safety button has tripped.
6. Allow the lower suction pipe to click into place in the
upper suction pipe.
Note
The upper and lower suction pipe can no longer be de-
tached from each other.
Illustration G
7. Open the protective grid.
Illustration H
a Unscrew the fixing screw on the protective grid.
b Open the protective grid.
8. Click the suction pipe in place in the motor casing.
Illustration I
a Pull out the motor casing locking pin as far as
possible.
b Insert the suction pipe into the motor casing.
c Insert the motor casing locking pin and check that
it is correctly seated in the holder.
9. Lock the suction pipe with the slider.
Illustration J
10. Secure the protective grid on the suction pipe.
Illustration K
a Fold the protective grid onto the suction pipe.
b Insert the clip of the latch into the adapter of the
protective grid.
c Push the latch down.
11. Install the collecting bag, see chapter Installing the
collecting bag.
Installing the collecting bag
Depending on the desired operating mode, the collect-
ing bag can either be hooked into the eyelet on the suc-
tion pipe or into the eyelet on the blower pipe.
1. Install the collecting bag.
Illustration L
a Pull the collecting bag on the adapter over the
connecting piece.
b Allow the adapter to click into place.
c Hook the tab of the collecting bag into the eyelet
on the suction pipe or, in the case of operation
without a suction pipe, into the eyelet on the blow-
er pipe.
Hooking the carrying belt
1. Hook the carrying belt into the eyelet on the handle,
making sure the quick release is accessible at all
times.
Illustration M
WARNING
Risk of injury due to incompletely assembled de-
vice
Only operate the appliance once it is fully assembled
and functional.
CAUTION
Risk of injury from objects flying about
Wear safety goggles and suitable protective gloves for
all work with the device.
The cordless aspirator has the following control ele-
ments:
● A speed control lever to regulate the speed of the
airflow steplessly.
● A selector lever to switch between the blow and suc-
tion modes.
● A slider for locking / unlocking the suction pipe to
connect the suction pipe to the motor casing or to
separate it from the motor casing.
● A blower pipe unlocking button to separate the blow-
er pipe from the motor casing.
Inserting the battery pack
ATTENTION
Dirty contacts
Damage to the device and battery
Check the battery mount and the contacts for soiling
and clean them as necessary before inserting the bat-
tery.
Illustration N
1. Push the battery into the mounting in the device until
it audibly latches into place.
Switch on the device (suction mode)
CAUTION
Risk of injury from flying parts and hearing damage
due to noise
Always wear eye and hearing protection.
WARNING
Risk of injury due to loss of control
Always hold the device with both hands on the provided
handles.
1. Insert the battery pack, see chapter Inserting the
battery pack.
2. Start the device.
Illustration O
a Set the selector lever to suction mode.
b Press the trigger.
The device starts up.
c Use the speed regulation to adjust the amount of
airflow.
Switch on the device (blower mode)
CAUTION
Risk of injury from flying parts and hearing damage
due to noise
Always wear eye and hearing protection.
English
Operation
Control elements
17