MSW Motor Technics MSW-MS-14 Manuel D'utilisation page 4

EN
TECHNICAL DATA
Parameter description Parameter value
Product name MOTORCYCLE STAND
Model MSW-MS-14
690 x 380 x 360/
Dimensions [mm]
780 x 460 x 400
Weight [kg] 4,14 + 4,74
Maximum motorcycle
200
weight [kg]
1. GENERAL DESCRIPTION
The user manual is designed to assist in the safe and
trouble-free use of the device. The product is designed
and manufactured in accordance with strict technical
guidelines, using state-of-the-art technologies
components. Additionally, it is produced in compliance
with the most stringent quality standards.
DO NOT USE THE DEVICE UNLESS YOU HAVE
THOROUGHLY READ AND UNDERSTOOD THIS
USER MANUAL.
To increase the product life of the device and to ensure
trouble-free operation, use it in accordance with this user
manual and regularly perform maintenance tasks. The
technical data and specifications in this user manual are
up to date. The manufacturer reserves the right to make
changes associated with quality improvement. The device
is designed to reduce noise emission risks to a minimum,
taking into account technological progress and noise
reduction opportunities.
LEGEND
Read instructions before use.
WARNING! or CAUTION! or REMEMBER!
Applicable to the given situation (general
warning sign).
Wear protective gloves.
ATTENTION! Hand crush hazard!
ATTENTION! Suspended weight!
PLEASE NOTE! The drawings in this manual are for
illustration purposes only and in some details may
differ from the actual machine.
The original operation manual is in German. Other
language versions are translations from German.
2. USAGE SAFETY
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in serious injury or even
death.
The terms "device" or "product" are used in the warnings
and instructions to refer to MOTORCYCLE STAND.
6
U S E R M A N U A L
a) Make sure the workplace is clean and well lit. A
messy or poorly lit workplace may lead to accidents.
Try to think ahead, observe what is going on and use
common sense when working with the device.
b) If you are unsure about whether the product is
operating correctly or if you find damage, please
contact the manufacturer's service centre.
c) Only the manufacturer's service point may repair the
device. Do not attempt any repairs independently!
d) Children or unauthorised persons are forbidden to
enter a work station. (A distraction may result in loss
of control over the device).
e) Please keep this manual available for future
reference. If this device is passed on to a third party,
the manual must be passed on with it.
f) Keep packaging elements and small assembly parts
in a place not available to children.
g) Keep the device away from children and animals.
and
h) If this device is used together with another
equipment, the remaining instructions for use shall
also be followed.
i) Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
j) The device is not designed to be handled by persons
(including children) with limited mental and sensory
functions or persons lacking relevant experience
and/or knowledge unless they are supervised by
a person responsible for their safety or they have
received instruction on how to operate the device.
k) When working with the device, use common sense
and stay alert. Temporary loss of concentration while
using the device may lead to serious injuries.
l) Do not overestimate your abilities. When using the
device, keep your balance and remain stable at all
times. This will ensure better control over the device
in unexpected situations.
m) The device is not a toy. Children must be supervised
to ensure that they do not play with the device.
n) When not in use, store in a safe place, away from
children and people not familiar with the device who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
o) Keep the device out of the reach of children.
p) To ensure the operational integrity of the device, do
not remove factory-fitted guards and do not loosen
any screws.
q) When transporting and handling the device between
the warehouse and the destination, observe the
occupational health and safety principles for manual
transport operations which apply in the country
where the device will be used.
r) Do not move, adjust or rotate the device in the
course of work.
s) It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
t) Keep the device away from sources of fire and heat.
u) Do not overload the device.
v) The device should only be used on a flat and level
surface, with appropriate load bearing rating.
w) Do not use the device outdoor during heavy wind.
Rev. 18.03.2021
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
The product is intended for holding the motorcycle in a
vertical position, slightly raised above the ground.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
C2 C3
D
A B D C1
A. Castors
B. Frame
C. Motorcycle support adapters
D. Handles for transport and manoeuvring
3.2. PREPARING FOR USE
APPLIANCE LOCATION
Keep the device away from any hot surfaces. The device
should always be used when positioned on an even, stable,
clean, fireproof and dry surface, and be out of the reach
of children and persons with limited mental and sensory
functions.
ASSEMBLING THE APPLIANCE
Mount the wheels in the sleeves on the rounded corners
of the A-shaped profiles using M10 bolts, washers and
self-locking nuts. Then insert two "A" corner profiles of the
same size into the main frame (the part with the transport
handle) until the holes are aligned in both of them. Insert
M8 bolts into these holes and tighten at the ends using
washers and nuts. At the ends of the stand intended for the
front fork, attach the spring-loaded forks and secure their
ends with a clip. In the case of the stand for the rear rocker
arm, first select the adapters for the given motorcycle, then
insert them into the holes at the ends of the stand, adjust
their distance and fix them in position using the knobs.
3.3. DEVICE USE
Drive the stand under the motorcycle wheel, making sure
that it is centrally located inside the device, i.e. between
the frame bars. In the case of the rear wheel, first fit the
adapters for e.g. the rocker arm (see the second photo
below) or the rocker rollers (sliders or paddock - see the
last photo below). Place the stand level with the ground so
that it lifts the motorcycle. In the case of the front wheel,
place the springy fork under the motorcycle fork (first
photo below).
Rev. 18.03.2021
EN
3.4. CLEANING AND MAINTENANCE
a) Use only non-corrosive cleaners to clean the surface.
b) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
c) Do not spray the device with a water jet or submerge
it in water.
d) The device must be regularly inspected to check its
technical efficiency and spot any damage.
e) Use a soft cloth for cleaning.
f) Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used to
construct the device can be recycled in accordance with
their markings. By choosing to recycle you are making
a significant contribution to the protection of our
environment.
Contact local authorities for information on your local
recycling facility.
7