TECHNICAL DATA
Parameter description
Parameter value
Product name
Metal Sheet Cutter
Drill Attachment
Model
MSW-DRNB2
Operating speed [rpm]
3,000
Minimum cutting diameter [mm]
24
Maximum
iron or steel plate
1.8
thickness
stainless steel
1.2
of cut
plate
material
[mm]
copper or
2.0
aluminum plate
plastic or
2.0
fiberglass plate
Dimensions [mm]
178x52x85
Weight [kg]
0.4
1. GENERAL DESCRIPTION
The user manual is designed to assist in the safe and
trouble-free use of the device. The product is designed
and manufactured in accordance with strict technical
guidelines,
using
state-of-the-art
technologies
components. Additionally, it is produced in compliance
with the most stringent quality standards.
DO NOT USE THE DEVICE UNLESS YOU HAVE
THOROUGHLY READ AND UNDERSTOOD THIS
USER MANUAL.
To increase the product life of the device and to ensure
trouble-free operation, use it in accordance with this user
manual and regularly perform maintenance tasks. The
technical data and specifications in this user manual are
up to date. The manufacturer reserves the right to make
changes associated with quality improvement.
LEGEND
Read instructions before use.
WARNING! or CAUTION! or REMEMBER!
Applicable to the given situation (general
warning sign).
Wear protective goggles.
Wear protective gloves.
PLEASE NOTE! Drawings in this manual are for
illustration purposes only and in some details may
differ from the actual product.
The original operation manual is written in German. Other
language versions are translations from the German.
2. USAGE SAFETY
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury or even death.
6
The terms "device" or "product" are used in the warnings
and instructions to refer to <Metal Sheet Cutter Drill
Attachment>.
2.1. SAFETY IN THE WORKPLACE
a)
Make sure the workplace is clean and well lit. A messy
or poorly lit workplace may lead to accidents. Try
to think ahead, observe what is going on and use
common sense when working with the device.
b)
If you discover damage or irregular operation,
immediately switch the device off and report it to
a supervisor without delay.
c)
If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
d)
Only the manufacturer's service point may repair the
device. Do not attempt any repairs independently!
e)
The device produces dust and debris during
operation. It is important to protect bystanders from
their harmful effects.
f)
Regularly inspect the condition of the safety labels. If
the labels are illegible, they must be replaced.
g)
Please keep this manual available for future
reference. If this device is passed on to a third party,
the manual must be passed on with it.
h)
Keep packaging elements and small assembly parts
in a place not available to children.
i)
Keep the device away from children and animals.
j)
If this device is used together with another
and
equipment, the remaining instructions for use shall
also be followed.
REMEMBER! When using the device, protect children
and other bystanders.
2.2. PERSONAL SAFETY
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b)
The device is not designed to be handled by persons
(including children) with limited mental and sensory
functions or persons lacking relevant experience and/
or knowledge unless they are supervised by a person
responsible for their safety or they have received
instruction on how to operate the device.
c)
When working with the device, use common sense
and stay alert. Temporary loss of concentration while
using the device may lead to serious injuries.
d)
Use personal protective equipment as required
for working with the device, specified in section 1
(Legend). The use of correct and approved personal
protective equipment reduces the risk of injury.
e)
Do not overestimate your abilities. When using the
device, keep your balance and remain stable at all
times. This will ensure better control over the device
in unexpected situations.
f)
Do not wear loose clothing or jewellery. Keep hair,
clothes and gloves away from moving parts. Loose
clothing, jewellery or long hair may get caught in
moving parts.
g)
Remove all adjusting tools or spanners before turning
the device on. A tool or spanner left in the revolving
part of the device may cause injury.
h)
The device is not a toy. Children must be supervised to
ensure that they do not play with the device.
Rev. 04.09.2019
2.3. SAFE DEVICE USE
a)
Do not overload the device. Use the appropriate tools
for the given task. A correctly-selected device will
perform the task for which it was designed better and
in a safer manner.
b)
When not in use, store in a safe place, away from
children and people not familiar with the device who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
c)
Keep the device in perfect technical condition. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
d)
Keep the device out of the reach of children.
e)
Device repair or maintenance should be carried out by
qualified persons, only using original spare parts. This
will ensure safe use.
f)
To ensure the operational integrity of the device, do
not remove factory-fitted guards and do not loosen
any screws.
g)
Do not touch articulated parts or accessories unless
the device has been disconnected from the power
source.
h)
Do not leave this appliance unattended while it is in
use.
i)
Clean the device regularly to prevent stubborn grime
from accumulating.
j)
Do not work on two workpieces at the same time.
k)
The device is not a toy. Cleaning and maintenance may
not be carried out by children without supervision by
an adult person.
l)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
m)
Keep the device away from sources of fire and heat.
n)
When processing elements, pay attention to
bystanders and their safety.
o)
Carefully observe the element during processing
in order to respond to a threat in time or prevent
damage of the element.
p)
Keep a workplace clean and remove all dust, shards
and unnecessary parts of the element after processing.
q)
The material to be processed should be free from dirt.
r)
Use protective gloves to avoid injuries made by sharp
edges.
s)
When using the device, process only the elements
of parameters accordant with the data given in the
technical data table. Do not exceed the permissible
dimensions of the workpiece.
t)
Long workpieces must be supported and set stably
for processing.
u)
Do not start cutting before starting the engine.
v)
During operation, the device should be kept vertically
to the workpiece (do not tilt the device sideways, it
may reduce efficiency and damage the cutting knife).
w)
Before using the tool, check and tighten all bolts and
nuts.
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there is
still a slight risk of accident or injury when using the
device. Stay alert and use common sense when using
the device.
Rev. 04.09.2019
3. USE GUIDELINES
The product should be attached to the drill as a tool intended
for cutting sheet metal.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
2
4
1
3
5
1.
Handle
2.
Main body
3.
Wrench
4.
Handgrip
5.
Knife handle
Other elements are presented on the illustrations further
in the manual:
6.
Clamping screw
7.
Drill chuck
8.
Clamping screw and nut
9.
Coil spring
10.
Clamping hole
11.
Sliding block
12.
Cover
13.
Locking screw
3.2. DEVICE USE
3.2.1. OPERATING:
•
Fasten the workpiece in the workplace so that the
distance between the workpiece and the surface of
the working table is at least 15 cm.
•
Fasten the tool to a drill by attaching it to the drill
chuck.
6
7
1
4
3
•
Do not start the device until a drive motor has
completely started.
•
Before finishing operation, pull the cutting blade out
of the plate while the engine is still running.
•
Special oil/cooling grease should be used during
operation.
3.2.2. HANDLE – ASSEMBLY/DISMANTLING
1.
Loosen the clamping screws with the wrench.
2.
Screw the handle out or in.
3.
Tighten the clamping screws with the wrench.
7